Drywall - Recent Questions, Troubleshooting & Support


Drill appropriate size hole for the anchor should be in the instructions pound the anchor in with a nut screwed on to the first few threads so they aren't damaged by pounding the anchor in remove nut install what your mounting put washer and nut back on tighten them up. That's it.

Red Head Js-38c... | Answered on Sep 30, 2019


I don't think a Dremel has enough power to do what your after. However there is a larger rotary tool made by several different company's mine is made Dewalt works great fairly inexpensive and will do what you need.

Drywall | Answered on Sep 30, 2019


The stud finders are not expensive but you can sometimes use a magnet to find the nails. Also you might try shining a flashlight across the wall. The putty put over the nails will sometimes show up. Last resort is to tap on the wall and try and hear the areas that have support under them.

Drywall | Answered on Jul 19, 2019


5/8 of an inch is recommended. You may be able to get away with 1/2 inch if you don't really care, but i would check with the building inspector first

Drywall | Answered on Jul 19, 2019


Circles are hard to make, I had a lot of trouble when we decided to put recess lighting into the whole house. I wasn't able to find a tool that does all the cutting for you but what worked really well for me was a Goldblatt Drywall Circle Cutter. It doesn't cut all the way through the drywall, it just scores it so that all you have to do is cut from the center of the circle out to the edge and then snap off the pieces. Saves you tons of time trying to get those round edges to look perfect!

Drywall | Answered on Jul 17, 2019


What application are you wanting to use it for?

Hilti Anchor.... | Answered on Apr 10, 2019


Screws if you have not already used. Then as follows:
Joint compound
Joint tape
Then texture if desired
Primer
Paint

Drywall | Answered on Mar 03, 2019


you tape and mud the joints after hanging the drywall

Drywall | Answered on Jul 01, 2018


If you are asking how to install drywall the best way is with screws.

Bruno Scooter... | Answered on Apr 10, 2018


You can either measure up from the floor or the piece of drywall you just hang and then measure over from the wall or the piece of drywall you just hang or you can put the drywall in place and I ball behind it and Mark with a pencil and then cut it out with a dremel tool and you should be good from there. You might want to use a keyhole saw or a roto zip and a Rotozip is the best way to do it but it takes a little practice in order to control it

Drywall | Answered on Mar 01, 2018


Thermal couple is a sencing wire that sends a signal to your gas valve when the tip Spence’s heat from a pilot light! Can be purchased at any hardware or big box store,eg. Home Depot/ Lowe’s And any plumbing supply store. Average price is $$6-8.

Nicor Lighting... | Answered on Feb 05, 2018


many home improvement stores sell partial sheets . then you cut a plug the right size and spackle it in place .

Drywall | Answered on Dec 17, 2017


hi there.
Sink A Self-Drilling (Threaded) Anchor
  1. Mark your hanging point with a pencil.
  2. Tap the pointed tip of the anchor into the wall with a hammer.
  3. Once the tip is in the drywall, with a screwdriver, screw the anchor in until it's flush to the wall.

Fix-It Friday: Anchors Aweigh! How To Put Anchors Into Walls

womenyoushouldknow.net/fix-it-friday-anchors-aweigh-how-to-put-anchors-into-walls/
How to Install Drywall Anchors to Hang Heavy Stuff on Your Walls
How do hang an object using drywall anchors Google Search

Drywall | Answered on Nov 28, 2017


Sometimes you can wrap a piece of thin plastic or paper around the stem and shove it back in and will hold it in place,- other wise there is a spring steel clip that probable wore out and would need to be replace but it wont be fun

Bosch SG45 4500... | Answered on Nov 02, 2017


Just saw your question but no answer. Sorry about the repair on the glass tape. Crack are pretty common with mesh tape, especially if the mesh was covered with premix all purpose compound. Mesh tape should be covered with setting type compounds. More info can be found on the tapebuddy.net how-to manual. They cover the reasons for the different compounds.

FibaTape Drywall... | Answered on Oct 18, 2017


Yes-just let dry after-then on prep of wall after you may have to skim wall with a thin coat of drywall compound and sand smooth

Klean-Strip... | Answered on Oct 02, 2017


it usually has that on the label-depends on which gun you have also

Makita LXSF01... | Answered on Oct 02, 2017

Not finding what you are looking for?
Drywall Logo

79 questions posted

Ask a Question

Usually answered in minutes!

Top Drywall Experts

ray gallant
ray gallant

Level 3 Expert

65422 Answers

John Donghia Jr.
John Donghia Jr.

Level 2 Expert

47 Answers

Bill Boyd

Level 3 Expert

53755 Answers

Are you a Drywall Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...