Health & Beauty - Page 5 - Popular Questions, Answers, Tips & Manuals
No power from control arm to chair
If your Dalton Primechair is not receiving power from the control arm, there could be several reasons for this issue. Here are some troubleshooting steps you can take:
Check Power Source:
Make sure the chair is plugged into a working power outlet.
Check the power cord and ensure it is securely connected to both the chair and the electrical outlet.
Power Switch:
Verify that the power switch on the control arm is in the "ON" position.
If there is a separate power switch on the chair's body, ensure it is also turned on.
Batteries (If Applicable):
If the chair uses batteries, check if they are properly installed and functional. Replace the batteries if necessary.
Remote Control (If Applicable):
If the chair comes with a remote control, ensure that the batteries are installed correctly and that the remote is functioning.
Fuse:
Check if there is a fuse in the power supply line or within the control arm. If the fuse is blown, replace it with a new one of the same type and rating.
Wiring Connections:
Inspect the wiring connections from the control arm to the chair. Look for any loose or disconnected wires. Reconnect any loose wires securely.
Faulty Control Arm or Power Supply:
If none of the above steps resolve the issue, there may be a fault in the control arm or the power supply system. Contact the manufacturer's customer support for further assistance. They may provide guidance on troubleshooting or recommend professional service.
User Manual:
Refer to the user manual for troubleshooting tips and specific instructions related to the Dalton Primechair.
If you are unable to resolve the issue with these steps, it's advisable to seek assistance from the manufacturer's customer support or contact a professional technician who is familiar with the specific model of your chair.
Hi I have a Dynamic DL 4.2i electric wheelchair, when it is turned on the leds just flash and chair won't move .
If your Dynamic DL 4.2i electric wheelchair is experiencing issues where the LEDs are flashing and the chair won't move despite fully charged batteries, there could be several potential reasons for the problem. Here are some troubleshooting steps you can take:
- Check for Error Codes:
- Electric wheelchairs often have a diagnostic system that uses flashing LEDs to indicate specific error codes. Refer to the user manual for your wheelchair to interpret these codes. They can provide valuable information about the nature of the issue.
- Inspect Connections:
- Ensure that all the electrical connections, including those between the controller, motors, and batteries, are secure and free from corrosion. Loose or damaged connections can disrupt the functioning of the wheelchair.
- Reset the Controller:
- Some wheelchairs have a reset button on the controller. Try resetting the controller by turning off the power, waiting for a few seconds, and then turning it back on.
- Check Joystick Operation:
- Verify that the joystick is functioning correctly. Sometimes, issues with the joystick or its wiring can affect the chair's performance.
- Test Batteries:
- Even though you mentioned that the batteries are fully charged, it's worth checking their voltage and overall health. Faulty batteries can still show a full charge but may not provide sufficient power.
- Controller or Motor Issues:
- If the problem persists, there could be an issue with the controller or the wheelchair's motors. In such cases, it's recommended to contact the manufacturer's customer support or a qualified technician for further diagnosis and assistance.
- Professional Inspection:
- If the wheelchair is still under warranty, consider contacting the manufacturer's customer support for assistance. If not, seeking the help of a professional technician with experience in electric wheelchair repairs may be necessary.
Always prioritize safety when troubleshooting or attempting to fix issues with electric wheelchairs. If you are unsure or uncomfortable performing the troubleshooting steps yourself, it's best to seek professional assistance to ensure the wheelchair is properly diagnosed and repaired.
How to recalibrate a digital food scale
They are not normally capable of recalibration. You need a very special certified calibration weight. They are done at the factory and that is it. As long as the scale is on a flat level, firm surface they should be good.
Full 'make model (what it is)' in all questions please. We can search and see if it is a known issue and if the company are recalling them.
How to get battery out of weight scale please?
Postal scale, bodyweight scale, kitchen scale, every scale ever made?
Turn it over, look for a door or a screw, unless it is the only Taylor Scale that has a sealed for life battery and is not replaceable.
'make model (what it is)' in all questions, first 3 words please.
..
Not finding what you are looking for?
