Food Mixers - Page 9 - Recent Questions, Troubleshooting & Support

0helpful
1answer

Is is worth repairing a Kenwood Prospero stand mixer km24?

If you have a multi meter check the box caps and resistors for KM 2XX series then replace it whenever required. Some may differ in values like 0.15uF 275x2, 0.33uF 275X2 or 0.47uF 275X2 then resistors may also differ with different models but common to have 1.1k ohms 2watts. Also if caps are open it is good to check the 600V triac and replace it when giving out lower output. I also advise to clean the commutator esp when is is sparking a lot, you may use light sanding and clean it after. Check also if the tachometer is good, there is a resistor-like-coil hidden under a plastic tab with 2 wires. This gives feedback and via a magnet attached to the shaft. Check the motor brush if it is good or worn out. Lastly check all the switches because if one of them is not working properly you wont be able to let the motor run.
3/15/2022 9:48:12 AM • Kenwood Food... • Answered on Mar 15, 2022
10helpful
3answers

K-beater is stuck on our Kenwood Chef and we can't remove it

I couldn't remove the K-Beater as when I tried to turn it the whole mechanism turned with it. I couldn't even remove the splashguard! I was going to take it to the Kenwood factory (a few miles from home) but then I thought I'd give it one more go and this is what I did...
  1. Next to where the K-Beater attaches in the middle of the circular plate is a lug with a pointed-shape bolt on the end. Remove this with a spanner and the beater plus gear cog can be removed.
  2. Place some mole grips or wide pliers on a worktop and sit the cogged gear in to it and grip so that it won't turn.
  3. Now you should be able to remove the K-Beater!
Perhaps someone can suggest how to stop it happening again. I haven't attached anything since but will update this post if I have any other helpful tips.
3/5/2022 7:19:16 PM • Kenwood KM400 /... • Answered on Mar 05, 2022
0helpful
1answer

Need new Beaters for a Emerson hand mixer Model # EM82821

see if they look like these https://www.dontwasteyourmoney.com/best-hand-mixer-replacement-beaters/ Unfortunately Emerson are a Television company which means their mixers are made by someone else and badged 'Emerson'. https://www.google.com/search?q=Emerson+EM82821+spares ..
3/3/2022 5:56:47 AM • Emerson Food... • Answered on Mar 03, 2022
6helpful
2answers

My blade assembly broke. Can I get a new one for my Maxi 4000

replacement can be found on amazon, take a look here: Amazon com Vitamix blade assembly. I hope this was helpful. Cheers
2/28/2022 5:25:44 AM • Vitamix Vita Mix... • Answered on Feb 28, 2022
0helpful
1answer

Can i use it to make panko?

Panko are made with a special non-fermented bread that has no crust. You can however make good breadcrumbs with old hard bread and if you want it to be like Panko, pulse it and leave the crumbs coarse. I am a trade chef and use Panko a lot. Panko (???) is a type of flaky bread crumbs used in Japanese cuisine as a crunchy coating for fried foods, such as tonkatsu. Panko is made from bread baked by electrical current, which yields a bread without a crust, and then grinding the bread to create fine slivers of crumb.[1] It has a crisper, airier texture than most types of breading found in Western cuisine and maintains its texture baked or deep fried, resulting in a lighter coating.[2] Outside Japan, its use is becoming more popular in both Asian and non-Asian dishes. It is often used on seafood and is often available in Asian markets, speciality stores, and, increasingly, in many large supermarkets. Panko is produced worldwide, particularly in Asian countries, including Japan, Korea, Malaysia, Thailand, China, and Vietnam.
2/26/2022 5:54:01 PM • KitchenAid Food... • Answered on Feb 26, 2022
0helpful
1answer

How do the governor and speed control plate work in a Hobart Kitchenaid K5-A stand mixer?

Before you swap it out, get a can of electrical contact cleaner and spray the track and contacts.
2/22/2022 3:20:17 PM • KitchenAid Food... • Answered on Feb 22, 2022
0helpful
1answer

Please I am a food equipment tech, and need a manual for a Hobart A 200 mixer, gear placement, this mixer is the old style with the small spring on main shaft to assist into 2nd

You can get the manual with the link provided. https://www.partstown.com/modelManual/HOB-A200_spm.pdf
2/1/2022 5:45:27 PM • Hobart Food... • Answered on Feb 01, 2022
1helpful
1answer

Service manual for hobart mixer s301

Give me the serial number,also hobart does'nt release their service manuals to the general public.However if you goto hobartcorp.com type in your model which is a d300 and you can access an exploded view of the parts.I work for hobart and service these mixers often.Any questions let me know.
2/1/2022 5:39:51 PM • Food Mixers • Answered on Feb 01, 2022
0helpful
1answer

My hand mixer is turbo and I put the beater with collar in the smaller socket instead of the bigger one and it is stuck, what should I do?

Take a 4 foot length of string and put it through the loops of the stuck beater. Tie the end of the string in a knot. Put the loop of string under your foot and hold the body of the mixer and pull.
1/22/2022 1:38:14 AM • Food Mixers • Answered on Jan 22, 2022
0helpful
1answer

How to remove the front of a sunbeam mixer

Thanks Anonymous for your answer back in 2008 regarding how to remove the front fascia by removing the beater eject button. I'm quite handy but spent over an hour trying to find how to remove the chrome front fascia. Even the service manual is just an exploded diagram with no obvious explanation of how to remove it. Many thanks, 13 years later!
1/21/2022 9:14:34 PM • Sunbeam 2350... • Answered on Jan 21, 2022
0helpful
1answer

I have a Kenwood Chef

Send me your email address and i will send you some info on how to repair it with modern components........... very easily done.

Send to bisley_bullet49 at hotmail dot com
1/21/2022 3:02:30 PM • Kenwood KM800... • Answered on Jan 21, 2022
0helpful
1answer

Will a Hobart dough hook fit a Univex M-20, 20 Quart Mixer

Better to buy the right one for the Univex M-20. They are readily available. https://www.google.com/search?q=dough+hook+fit+a+univex+m-20+mixer ..
1/19/2022 12:41:30 AM • Hobart Food... • Answered on Jan 19, 2022
0helpful
1answer

Model A701. What type of grease/oil is used in the gearbox and how much?

A white or clear lithium grease. Do not cake it on but enough to get into all of the cogs/worm gears.
1/12/2022 2:35:19 AM • Kenwood Food... • Answered on Jan 12, 2022
0helpful
1answer

KitchenAid Artisan mixer accessory port not turning

You probably just need a new Shear Pin. This is just a small steel pin like a nail that goes through the gear and the drive shaft. If the strain on the final drive exceeds specs, the pin shears through and thereby saves damage to the gears and motor. Google make model parts diagram https://www.ereplacementparts.com/kitchenaid-4ksm150psbw0-artisan-tilt-head-stand-mixer-parts-c-114958_114959_115458.html This is one of the Shear Pins. They just call it 'pin, retaining'. https://www.ereplacementparts.com/shear-pin-retaining-pin-p-621981.html ..
1/7/2022 4:42:10 PM • KitchenAid... • Answered on Jan 07, 2022
Not finding what you are looking for?
Food Mixers Logo

8,911 questions posted

Ask a Question

Usually answered in minutes!

Top Food Mixers Experts

ADMIN Eric
ADMIN Eric

Level 3 Expert

39363 Answers

john h

Level 3 Expert

29494 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66835 Answers

Are you a Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...