Audio Players & Recorders - Page 4 - Recent Questions, Troubleshooting & Support

Carlsbro are still in business. Have you tried them direct? Not much available on this vintage amp but there is a review. https://www.google.com/search?q=Carlsbro+Power+Module+6+channel The extra jack on the speaker is probably for piggy backing. They would have to have a different type of plug and be marked and also also have a fuse it it was mains powered or even 100 volt line powered . ..

Running it through a computer using DDL? https://www.google.com/search?q=creative+5.1+system+volume+control+problems ..

Contact their Support number. The Update Discs are corrupt and need replacing. https://www.google.com/search?q=sound+leisure+digital+jukebox+not+updating+software ..

• i think the problem is due to dust
• using a vaccum cleaner or use a painting brush for clean the IC legs and ciruit
• check loose conection of the control
• the dust mis function the chip inside

wish you all the best

Check the Remote Control: Ensure that the remote control is functioning correctly. Press the MUTE button on the remote control to unmute the sound. The "MUTE" indicator should turn off. Manual Adjustment: Navigate to the receiver's setup menu and locate the audio settings section. Adjust parameters such as bass, treble, balance, and surround sound modes to achieve your desired audio quality. Physical Connections: Verify that all audio cables are securely connected to the appropriate inputs and outputs. Check if any cables are damaged or loose. Speaker Configuration: Make sure your speakers are correctly configured. If they are set to "Mute", unmute them. Factory Reset: Refer to the instruction manual for instructions on performing a factory reset.

Open it up and look for bulging or split electrolytic capacitors, especially in the back to the display and the power supply. Or take to an electronics technician for diagnosis. https://www.google.com/search?q=Sony+deck+MHC+RV900D+not+working ..

It should read on the board, in the same place where it's fried on what type of resistor for replacement.

See if we can get it working: Charging Issue: If the green light is blinking, it might be indicating that the battery is low and needs charging. Connect your speaker to a charger and let it charge for at least 3 hours. The light should turn green when fully charged. Make sure you're using the correct charging cable and power source. Auxiliary Mode: A solid green light typically means the speaker is in AUX mode. This allows you to connect a non-Bluetooth device (like a laptop or MP3 player) to the speaker through the AUX port. To switch back to Bluetooth mode, press the MODE button (usually represented by three overlapping circles). This should turn the light blue, indicating that the speaker is ready to pair with your Bluetooth device. Check Connections: Ensure that there are no loose connections or faulty cables. If you're using an auxiliary cable, make sure it's securely plugged into both the speaker and your audio source. If you're using Bluetooth, try pairing the speaker with your device again. Reset the Speaker: Sometimes a simple reset can resolve issues. Turn off the speaker, disconnect it from any power source, and then turn it back on. Volume and Sound Settings: Adjust the volume on both your speaker and the connected device. Make sure the volume isn't too low or too high. Check if the sound is muted or if any equalizer settings need adjustment. Firmware Update: Visit the manufacturer's website or check the user manual for any available firmware updates. Updating the speaker's firmware might address compatibility issues. If none of these steps resolve the issue, consider reaching out to iCandy customer support for further assistance.

The nearest you will get is the service manual. Dowmload the service manual and follow the dissasambly and reassambly instructions to the letter, otherwise it will not work correctly and the timing will be out. https://elektrotanya.com/panasonic_sa-ak20.pdf/download.html

Being from 1985 or there abouts, it probably needs some TLC at a Yamaha service centre. May need new capacitors and resolder dry joints for age related issues.

WD-40 ... Very dangerous as it not only flammable when wet but is bad for electrical contacts as it leaves a residue behind that does not conduct electricity very well. Check speaker connections first.

The error may deprive you of options. But the "options" for a fix are pretty limited to the following: Contact IAG: Reach out to IAG, the manufacturer of Audiolab products. They can provide you with a set of codes to re-enable the missing options (such as MPEG2, HDCD, DTS, and Prologic II) if they disappear again. Corrupted EEPROM: The problem might be related to a corrupted EEPROM (Electrically Erasable Programmable Read-Only Memory). IAG's service technicians should be able to address this issue for you. Reset: While the manual doesn't explicitly mention a reset sequence for the Audiolab 8000AV, you can try the following steps: Press "analog + normal + video" buttons simultaneously. Then press the "display" button to restore factory settings. This may help regenerate a system code and potentially resolve the issue. Remember that this is a specific issue related to the Audiolab 8000AV, and contacting IAG for assistance is your best course of action

No, you must press mute again on the remote to toggle off mute.

You could put a peice of gaffa tape over the sensor window if you do not read schematics very well.

Well don't know if it will work for everyone but, I turned it upside down then hit the power button and let it run for a minute like that and Vwala. (Upside down out of the water FYI lol)

To switch the input on your Kenwood KRF-V7772D receiver from analog to digital or optical, follow these steps: Check the Manual: First, consult the user manual for detailed instructions specific to your model. If you don't have the manual, you can find it online. The manual provides step-by-step guidance on how to change inputs. Input Selector Button: On the front panel of your receiver, look for the Input Selector button. It might be labeled as "Input," "Source," or something similar. Press this button to cycle through the available input sources. On-Screen Menu: Some receivers allow you to change inputs using an on-screen menu. If your Kenwood receiver has this feature, navigate to the menu using your remote control. Look for an option related to input selection or source. Remote Control: Use your remote control to directly select the desired input. Look for buttons labeled with input sources (e.g., "DVD," "CD," "TV," "Optical," etc.). Press the appropriate button to switch to the desired input. Digital Inputs: If you want to switch to a digital input (such as optical or coaxial), ensure that your digital audio source (e.g., Blu-ray player, game console, etc.) is connected to the corresponding input on the back of the receiver. For optical input, connect the optical cable to the "Optical In" port. Analog Inputs: If you prefer an analog input, connect your analog audio source (e.g., turntable, cassette player, etc.) to the appropriate analog input on the back of the receiver. Remember to adjust the settings on your connected devices (e.g., TV, Blu-ray player) to output audio through the selected input on the Kenwood receiver. If you encounter any issues, refer to the service manual for further troubleshooting

Check Speaker Wiring: Ensure that the speaker wires are properly connected to the stereo unit. Loose or damaged wiring can cause sound interruptions. Inspect the connections at both ends (stereo unit and speakers) to make sure they are secure. Bluetooth Pairing Data: Since you've already reset the car stereo and deleted all devices, let's focus on Bluetooth. Go to the Settings menu on your Kenwood system. Select Bluetooth and look for the option to Clear All Paired Devices. This will remove any existing Bluetooth pairings. After clearing the paired devices, try reconnecting your phone or other Bluetooth devices to see if the sound returns. Device Reset: Sometimes a simple reset can help. Turn off the car stereo completely and disconnect the power source (e.g., by removing the car battery cable). Wait for a few minutes, then reconnect the power and turn the stereo back on. Check if the sound is restored. Firmware Update: Visit the Kenwood website and check if there are any firmware updates available for your model. If updates are available, follow the instructions to install them. Sometimes software updates can address audio-related issues. Blue TI Light Flashing: The flashing blue TI light over BT1 indicates that the stereo is trying to establish a Bluetooth connection. Make sure your phone or other Bluetooth devices are discoverable and within range. Try pairing your phone again and see if the sound works. Manual Reference: For more detailed troubleshooting steps, refer to the Kenwood Excelon DPX594BT user manual. The manual provides information on settings, troubleshooting, and common issues. Remember that car stereo issues can be caused by various factors, including wiring, software glitches, or hardware problems. If none of the above steps resolve the issue, consider seeking professional assistance or contacting Kenwood customer support.

If the file has been corrupted, there is no alternative than to use a newer file. You would know more than I regarding where to get that but, if you have a memory issue, a new file won't fix it. Run a memory check.

Probably nowhere as this is an Amazon / eBay special so made in China. You should be able to go to Windows Settings, - Hardware and tell Winderz to find a compatible driver. https://www.google.com/search?q=VIBE+SOUND+USB+Turntable+Model+VS-2001-USBT+drivers ..

Hi I have a manual (and an IQ Voice organizer that I'm trying to sell). I would happily send you a pdf file of the manual if you contact me. Robert