Pool & Spa - Page 3 - Recent Questions, Troubleshooting & Support

limited info generic answer u code doesnt show for intex their codes usually start with E this is a manual that has the trouble shooting on page 20 ------- https://www.manua.ls/intex/purespa/manual?p=1 --------- and pg 13 has the codes

all sides come off needs to fix or run another pipe

Testing the water pressure of your Hayward gas heater is a relatively simple process. Follow these steps to check if your water pressure is working properly:

1. Turn off the Gas Heater: Before performing any tests, make sure the gas heater is turned off to avoid any potential accidents or injuries.
2. Check the Pressure Gauge: Locate the pressure gauge on your Hayward gas heater. It is usually located on the front panel of the unit or near the plumbing connections.
3. Observe the Pressure Reading: The pressure gauge will display the current water pressure. It is typically measured in pounds per square inch (psi). The optimal water pressure for most pool heaters is usually between 15 psi to 25 psi, but it's essential to check your heater's manual for the specific recommended pressure range.
4. Turn on the Pool Pump: Ensure that the pool pump is running, as it is responsible for circulating the water through the heater. The water pressure will be at its most accurate when the pool pump is operating normally.
5. Monitor the Pressure: While the pool pump is running, observe the pressure gauge to see if the water pressure falls within the recommended range. If the pressure is below the minimum recommended level, it may indicate a circulation issue or a problem with the pool pump.
6. Check for Leaks: While testing the water pressure, inspect the heater and the surrounding plumbing connections for any signs of leaks. Leaks can lead to reduced water pressure and affect the heater's performance.

Most pool pump/filter systems are designed to achieve the minimum recommended flow rate. A pump system with at least 1HP motor should achieve the minimum flow rate, but a 0.75HP motor would likely also achieve it. The Hayward H series heaters do not include a water flow rate sensor, but rather use a water pressure sensor to verify the pump is operating. If the system has insufficient water flow even when the pressure is within normal operating limits, the heater will likely over heat and open the water pressure relief valve located on the outlet header. This condition could occur if the down-stream line is blocked (by a closed valve or similar condition). It is important to avoid this condition since the heater will release pressure via opening a relief valve, spilling water directly out of the heater manifold. The only adjustment for hydraulic sensing within the H series heaters is the water pressure sensor. See other articles within fixya for this procedure.

no info generic answer when pump is on [to make temp ] the jets are also on

Tony, Ck these sites on how to identify it... https://duckduckgo.com/?t=ffab&q=hot+tub+idendifier Best to you.

this car? https://www.facebook.com/InTheKnowInnovationAOL/videos/this-hot-tub-on-wheels-is-the-newest-party-vehicle/2427071604221605/

The code you are referring to is actually IF, not 1F. It stands for ignition failure. If the control exceeds the maximum number of ignition retries or recycles the heater will shut down and go into lockout. Automatic reset is 60 minutes.

If the controller for your Prowler 920 robotic pool cleaner is not turning on or powering up properly, here are a few steps you can take to troubleshoot the issue: 1. Check the Power Supply: Ensure that the power supply is properly connected to the controller and that it is receiving power. Verify that the power cord is securely plugged into a functioning power outlet. You can try plugging another device into the same outlet to confirm that it is working correctly. 2. Inspect the Controller Display: Take a close look at the display on the controller. If any error codes or messages are displayed, consult the user manual or contact the manufacturer for further instructions on how to resolve the specific issue indicated. 3. Reset the Controller: Try performing a reset on the controller. Look for a reset button or a combination of buttons to press and hold simultaneously for a few seconds. This action can often help resolve minor software glitches and restore the controller's functionality. 4. Check for Loose Connections: Ensure that all cables and connections between the controller and the power supply or the Prowler unit are securely plugged in. Sometimes, a loose or faulty connection can prevent the controller from turning on. 5. Replace Batteries: If your controller uses batteries, make sure they are not depleted. Try replacing the batteries with fresh ones and see if the controller powers up properly. 6. Contact Manufacturer Support: If the above steps do not resolve the issue, it's recommended to reach out to the manufacturer's customer support. They can provide you with further assistance, troubleshooting steps, or advise on any potential repairs or replacements that may be needed. Remember to consult the user manual that came with your Prowler 920 for any specific troubleshooting steps or contact information for customer support.

circulation pump failure

Hot Tub Error Codes - Spa Topside Error Messages

Hot Tub Essentials https://www.hottubessentials.ca > hot-tub-error-codes 1) Hot Tub Error Codes (Alphabetical) ; COOL, Spa water is more than 20° F cooler than the temperature set point ; CP-ER, Circ pump failure ; DR, dr, dy?

Here's the manual with setup information...https://www.manua.ls/intex/purespa/manual?p=9MY bad you'll have to copy and paste the link. :(

• not a car, moved yah
• ask the maker. for help/parts or all the installer for help.

google shows https://www.hottuboutpost.com/hydro-quip-6000-series-electronic-control-system-cs6209b-us-f/

google Mastercraft jet pump Model #561471 parts If it as described I would put new pump in. If you chose rebuild it A new is is $250 on eBay.

The error codes and buzzing sound you are experiencing with your Raypak RP2100 heater indicate potential issues with the ignition and flame sensing components. Here are some troubleshooting steps you can take: 1. Check Gas Supply: Ensure that there is an adequate supply of gas to the heater. Make sure the gas valve is fully open and that there are no obstructions or leaks in the gas line. 2. Inspect Ignition System: The CFH (Call For Heat) and SPK (Spark Ignition) codes suggest that the heater is having trouble igniting. Inspect the ignition system components, including the spark electrode, ignition control module, and wiring connections. Clean any debris or corrosion that may be affecting the spark ignition. 3. Check Flame Sensor: The buzzing sound you hear could be related to the flame sensing system. The heater may not sense the presence of a flame, causing it to shut down. Inspect the flame sensor for any buildup of soot, debris, or corrosion. Clean the flame sensor using a soft cloth or a non-abrasive brush. 4. Verify Proper Ventilation: Ensure that the heater's venting system is clear of any blockages. Blocked vents can lead to incomplete combustion and affect the heater's ignition process. 5. Consult the Owner's Manual: Refer to the owner's manual for your specific model of the Raypak RP2100 heater. It may provide additional troubleshooting steps and error code explanations that are specific to your unit. 6. Seek Professional Assistance: If the issue persists or you are unable to resolve it on your own, it's recommended to contact a professional technician who is experienced with Raypak heaters. They will have the expertise to diagnose and repair any complex issues with the ignition system. Remember, dealing with gas appliances can be dangerous. If you are not experienced with working on gas heaters, it is best to contact a qualified professional to ensure proper troubleshooting and repairs.

If the control panel indicator lights on your pool system do not consistently light up when the pool is turned on, it could indicate a potential issue with the control panel or the electrical connections. Here are some troubleshooting steps you can take: 1. Check Power Supply: Ensure that the power supply to the control panel is stable and consistent. Make sure the power source is providing the correct voltage and that there are no loose or faulty connections. 2. Inspect Wiring Connections: Verify that all wiring connections to the control panel are secure and properly connected. Loose or damaged wiring can cause intermittent issues with the indicator lights. 3. Clean and Inspect Control Panel: Check the control panel for any signs of dirt, debris, or corrosion. Clean the control panel and its components using a soft cloth and a mild cleaning solution. Inspect for any visible damage or loose components. 4. Test Indicator Lights: While the pool is running, observe the control panel and try to identify any patterns or triggers that may cause the indicator lights to come on. Gently tap on the control panel to see if it affects the lights. This could indicate a loose connection or a faulty component within the control panel. 5. Consult a Professional: If the issue persists or you are unable to identify the cause of the inconsistent indicator lights, it is recommended to contact a professional pool technician or the manufacturer's customer support for further assistance. They will have the expertise to diagnose and resolve the specific issue with your pool control system. Remember, working with electrical components requires caution. If you are not experienced or comfortable working with electrical systems, it is best to seek professional help to avoid any potential safety hazards.

To replace the wheel tubes on an Aquabot Bravo III robotic pool cleaner, follow these steps: 1. Prepare the Pool Cleaner: Turn off the power to the pool cleaner and remove it from the water. Place it on a flat surface, such as a table or workbench, for easier access to the wheels. 2. Remove the Wheels: Locate the wheels that need the tube replacement. The Bravo III usually has four wheels, two on each side. Each wheel has a hubcap covering the axle. Use a flathead screwdriver or your fingers to pry off the hubcap from each wheel. 3. Remove the Wheel Tubes: After removing the hubcap, you will see the wheel tube inside. Carefully pull the wheel tube out of the wheel assembly. You may need to twist and wiggle it gently to loosen it. If the tube is damaged or worn, it should come out easily. 4. Insert the New Wheel Tubes: Take the replacement wheel tubes and insert them into the wheel assembly. Make sure they are properly aligned and seated securely. 5. Replace the Hubcaps: Once the new wheel tubes are in place, put the hubcaps back onto the wheels. Press them firmly until they snap into place, ensuring they cover the axle and wheel tube. 6. Repeat for other Wheels: If you need to replace the tubes on multiple wheels, repeat the process for each wheel that requires a replacement. 7. Test the Pool Cleaner: Once all the wheel tubes are replaced and the hubcaps are securely in place, place the Aquabot Bravo III back into the water and test its operation. Ensure that the wheels are turning smoothly and that the pool cleaner is functioning properly. Note: It's recommended to refer to the specific user manual for your Aquabot Bravo III pool cleaner for detailed instructions and illustrations on how to replace the wheel tubes. The manual will provide you with any additional information or precautions specific to your model.

If the programming button on your Speck pumps E71-II VHV is not working and you're unable to enter the program menu, here are a few steps you can try to troubleshoot the issue: 1. Check the Button: Inspect the programming button for any physical damage or debris that may be obstructing its functionality. Clean the button gently with a soft cloth to ensure there are no obstructions. 2. Restart the Pump: Turn off the pump and unplug it from the power source. Wait for a few minutes, then plug it back in and power it on again. Sometimes, a simple restart can help resolve temporary issues. 3. Factory Reset: Refer to the user manual for instructions on how to perform a factory reset on the pump. This process will restore the pump to its default settings, including the programming function. Be aware that a factory reset will erase any existing programmed settings, so you will need to reprogram the pump after performing this step. 4. Contact Manufacturer Support: If the above steps do not resolve the issue, it's recommended to contact Speck pumps customer support directly. They can provide you with further troubleshooting guidance specific to your model and advise on any potential repairs or replacements that may be necessary. When reaching out to customer support, make sure to provide them with the specific details of the issue, including the model number (E71-II VHV), and any troubleshooting steps you have already attempted. They will be best equipped to assist you further and offer tailored solutions.

You didn't give us a Make and Model but here are some sites that answer that question for varied Makes.. https://www.google.com/search?q=digital+pool+heater+is+displaying+sw+open+error&source=hp&ei=ZoKPZO-nHLfF0PEP0-iW6A8&iflsig=AOEireoAAAAAZI-QdpNy-irsShPIybO1gAWJJK1zy3Tx&oq=digital+pool+heater+is+displaying+sw+open&gs_lcp=Cgdnd3Mtd2l6EAEYADIFCCEQoAEyBQghEKABUABYAGDsM2gAcAB4AIABjAKIAYwCkgEDMi0xmAEAoAECoAEB&sclient=gws-wiz

Possibly this may help... https://www.troublefreepool.com/threads/iaqualink-says-service-mode.99426/ Best to all.

See page 18 of the saltwater instruction guide ... 93 means it is on stand-by, power saving mode. Nothing is wrong, it's just waiting for the timer to tell it to turn back on automatically. If you want the system to be on right now, just turn the power switch off, wait a couple seconds and turn it back on.