Science & Laboratory - Page 5 - Recent Questions, Troubleshooting & Support

Contact MTN directly to request the manual.

well , use test lamp to find lost power. any desk lamp , turn it on then plug it in to all AC power jacks that connect to this AutoClave. (I assumed it is plug power and not hardwired to 240vac service) are you in uSA< posting to USA forums? why not just call and electrician and end this. not get shocked and all that. no power at all to your lab , the building or just one THING, .

That is an autoclave and peoples life and health depend on it. Please contact the manufacturer at +39 0445 329811

Make sure the unit is unplugged!!! I believe it is the lid switch. You can remove the housing and the switch is located adjacent to the latch. Test it with a multi-meter.I do not recommend bypassing the switch except to test it's operation. Serious injury can occur!!!

i have centrifuge from eppendorf model: 5402... it is old model so the user manual is not available on web.. it looks fine on start .. but when i start a run it gives error or "Balance rotor" ... i am checking it every electronics but everythings looks fine.. kindly guide me what i could do.. [email protected] i need manual

Dear Sir, In a 5402 Eppendorf Centrifuge, Error 1 states primarily for an EEPROM error. EEPROM is a tiny memory chip that stores individual details of the centrifuge, mainly the microprocessor time base (for correct time set operations), the mains voltage (115 or 230 V, to inform and set the motor current levels), and the imbalance level adjustment for the imbalance sensor. When the centrifuge powers up, these data are readen, and if all OK, the centrifuge is ready to go. If one of them corrupts, especially the 115 or 230 Volt information, we get Error 1 and no start allowed. To check and reprogram this EEPROM we have to acess the service routine. This is done by by jumping together pins 1 and 5 of X8 conector, on the base of the electronic board, located behind the power cable panel in the back of the centrifuge. There are about 20 setting or check parameters, but usually 1 or 2 of the described above need to be reprogrammed. Please e-mail me for details: [email protected]. Regards, Paulo H. F. Pimenta

Turn it on and bring up the temperature. The pressure inside will increase as the temperature increases.

https://www.amscope.com/?medium=tsa&msclkid=61e743301f171ac3f7fa1e0242a02b96&utm_source=bing&utm_medium=cpc&utm_campaign=Brand_Core_Exact&utm_term=amscope&utm_content=Amscope&gclid=CJujjbWcwuMCFU3LDQodSBECdg&gclsrc=ds

The fault table is on page 15 of the following document. http://frankshospitalworkshop.com/equipment/documents/autoclaves/service_manuals/Eschmann_SES2000_-_Service_Manual.pdf Further support may be channeled through the distributor. As with many devices, it is suggested to have mainteance and repair done by personnel trained specifically in such for the devices. There is quite a bit of information in this manual one might wade through Page 28 lists error codes and error 2 listed refers to door open during cycle. UK Customers Eschmann Equipment, Peter Road, Lancing, West Sussex BN15 8TJ, England. Tel: +44 (0) 1903 765040. Fax: +44 (0) 1903 875711. Overseas Customers Contact your local distributor. In case of doubt contact Eschmann Equipment.

I can only offer a user manual to the device. The next to last page of the manual lists contact information by country. You might see if you can get the answer from a listed source. https://www.grainger.com/ec/pdf/GasBadge-Pro-Instruction-Manual.pdf A prior Fixya answer offers the following: A reading of 221 ppm carbon monoxide gas is a dangerous level that should be taken seriously. You could try a new battery and reset the detector.

Sure, they can be downloaded easily by using this software: Driver Update Software for XP Vista 7 8. Wish you best of luck. Cheers

A User Manual for the Variscope Binocular 40x to 1000x microscopes is available from Amazon online: http://www.manuallibrary.net/1475-40x-1000x-biological-binocular-user-manual.html

There is information online about these sheep that may help answer your question: http://www.pedisheep.co.za/breed.htm http://gadi.agric.za/InfoPacks/2014025%20South%20African%20Sheep%20breeds%20-%20Pedi.pdf

Manuals are available from PHC. Email [email protected] or call Technical Support at 800-858-8442 ext. 48299.

You can get a PDF of this manual here:

http://photos.labwrench.com/equipmentManuals/11147-4444.pdf

Try here: https://www.optiboard.com/forums/showthread.php/8260-Lensometer

Contact Zeiss for service.

the-touch-screen-on-my-deluxe-lcd-digital-microscope-44345-doesn-t-respond-how-can-i-fix-this