Tools & Hardware - Others - Page 5 - Recent Questions, Troubleshooting & Support

Made in China and sold under different names. https://www.google.com/search?q=neiko+7+auto+polisher+manual ..

Is this https://multimedia.3m.com/mws/media/758876O/3mtm-electric-variable-speed-polish-instr-man-7-1000-3000rpm.pdf

Sorry but we do not buy or sell on this website. This is a site for repair advice and tips. Perhaps you could contact the original manufacturer of the sharpener or the place you bought it from. They may be able to supply parts or suggest where you could get them from.

Same problem, drive belt for a PC 371 compact belt sander. Solved using a 4 mm Allen key with short end inserted in the smaller drive gear to rotate the system. This is not as harsh on the tool as using the conduit pipe as shown in the utube video. Clamp the tool to a bench securely, with good lighting for visibility. Holding the belt partly on the larger gear and on top of the small gear, place the short arm of the Allen key through the open belt into the end of the small gear (4 mm was the correct size on mine). Then turn the Allen key withe long arm slowly while working the belt down onto the smaller gear. Not too easy, nut this will work with good finger presssure alone. Once engaged, keep working it down until its fully engaged (check carefully). I think it's helpful to drop the belt in hot water before this - doesn't make it stretch better, but the water seemed to help get the belt to move over the drive gear without damage.

There have a hidden button to turn on to do setting

Sorry, I was missing that part. You got it right, though. three hands is the answer. Orrr, you could go get some nice sticky back papers and cheat. They come in a variety of sizes or can be cut from full sheets. what you have there is a good sander to use while you figure out what kind of sander you want:)
Best regards, Farmerbear

It is not possible to do that. You can't search posters. You could have put a question in that post, or you could post your own question, something like make model drum sander. I need new abrasive rolls please. There are discs here https://www.google.com/search?q=4+1%2F2%22+sticky+discs+for+a+drum+sander Or just go for generic Drum Sander Sleeves https://www.google.com/search?q=drum+sander+sleeves ..

No, the TRE300 will require a wide crown staple. The staples that will work with the TRE300 are the TRC600 series( TRC604T 1/4" TRC605T 5/16" TRC606T 3/8").

ck here..... https://www.fixya.com/support/t23622347-need_spare_part_no_39_136068371

well the one best tool of all is banned Voltmete i can think of other ways but those tool you do not have. Some newer charger hooked up backwards tells you it it did. all mine do. no model Schumaker so no easy answer me reading you your users guide to you. here is mine see page 7 shows what backwards does LED INDICATORS CLAMPS REVERSED/ BAD BATTERY(red)LED flashing: The connections are reversed https://store-zm80kkpa03.mybigcommerce.com/content/manuals/0099001909-R0.pdf

Seven years later... sorry, man!— Solution — I have a Skil Belt Sander model 7313 which must be very similar if not the same. It has a 3/4HP motor, 3" x 18" belt capacity, a lever for belt release and a single Phillips screw for "adjusting auto-track" which is a misnomer in itself. Very odd. That screw is on the front left as you are using the sander, belt-down. When you "loosen" (CCW) this screw, the belt should move (if at all) toward the body of the sander; "tightening" it (CW) changes the angle of the front roller, which can force the belt off the open side. In my case I had to loosen it all the way just to slow it from slipping off the machine.My tolerances wore over time — or my belts were constructed poorly — so that the belt always rode off and away from the machine no matter where that screw was .So, I "shimmed" the roller closest to the adjustment with a 1/2" strip of duct tape one full wrap around (this made the end of the roller closest to the tracking adjustment "fatter." Tested it. It needed more. I added another piece of tape to the complete circumference of the roller, but this time 1" wide, covering the first tape right up to to the original edge, and over toward the middle. Tested it again. It needed more, but was improved. I added one more tape, 1-1/4" wide from the same edge out to the middle — effectively making a bit of a 'cone' toward the center, and this solved it for me. I think that in my case, the belts I bought at Home Depot were just a bit too long and needed this shimming method to take up slack. I found it easiest to make final adjustments "under load." Sand something right-handed using light pressure and adjust the screw with your left hand. (Note: this differs from the offical instructions in the manual: https://www.manualslib.com/manual/132374/Skil-7313.html?page=8.It may help to lubricate the pivot point of the front roller, which is actually about 4" back of the axel, right at the release lever's rivet, back inside the machine. If this pivot point is not fee moving, your auto adjust may not be able to allow proper rocking for adjustment.Also, with the belt off the machine, you can get a better idea of how the adjusting screw for the so-called auto-track feature does its work. Mine seems to have a lot of room to adjust it exactly the wrong direction, and no adjustment in the opposite direction. Hence my shimming idea.

Unfortunately, it appears that finding a manual for the Chicago Forge 9" disc and 6" belt sander may be difficult as the company no longer exists. However, there are a few things you can try to help with repairs and maintenance.

1. Look for similar models: Try looking for manuals for similar models of disc and belt sanders. Many of these machines have similar features and functions, so you may be able to find a manual that can help you with your repairs.
2. Check online forums: Look for online forums or discussion groups related to woodworking or metalworking. Many of these forums have members who are experienced with various tools and may be able to provide tips and advice on how to repair and maintain your sander.
3. Contact local repair shops: Check with local repair shops or machine shops that specialize in repairing power tools. They may have experience with this type of sander and be able to offer guidance on repairs and maintenance.
4. Experiment and tinker: Sometimes the best way to learn about a tool is to experiment with it and tinker around. Take the sander apart and see how it works, clean and lubricate the parts, and see if you can diagnose the problem. Just be sure to take safety precautions and follow proper procedures when working with power tools.

Good luck with your repairs and maintenance!

Question edited for clarity. Question moved from Televisions. https://www.google.com/search?q=hyper+tough+rotary+tool+won%27t+turn+on

If you have installed the ceramic balls in your Medicool 20K Pro Drill, and now it is not working, you may need to perform the following steps to fix it:

1. Remove the handpiece from the control box.
2. Unscrew the two small screws on the front of the handpiece.
3. Gently remove the front cover of the handpiece.
4. Remove the two ceramic balls from the spindle.
5. Reassemble the handpiece by replacing the front cover and securing it with the screws.
6. Reconnect the handpiece to the control box and test it.

If the drill still does not work, it may be a problem with the control box or another component. In that case, it may be necessary to contact the manufacturer or a professional repair technician for further assistance.

Question edited for clarity and spelling 'whipper' to 'wiper' Question moved to Silverado HD. https://www.google.com/search?q=2003+Chevy+Silverado+HD.+My+wiper+sticks+on+low+speed

Not sure where your located...but if you take the switch out and go to Grainger's I'm confident they can help you.

here is a link copy and paste https://sawmillcreek.org/showthread.php?111567-DeWalt-733-Rollers-stopped-moving ..

Question edited for clarity, 'Foredom', not 'ForedOOM'. Question moved from Washing Machines category. Likely to be a broken internal shaft cable. When they break they tie up and tangle in the sleeve. https://www.google.com/search?q=Foredom+stops+spinning

Epoxy glue

Remove the magazine and staples. Look down at the very end and look for a damaged bent staple. You can also check that the hammer is firing. https://www.google.com/search?q=Black+%26+Decker+9700+electric+stapler ..