Washing Machines - Popular Questions, Answers, Tips & Manuals

You posted your question under LG washing machines. Try reposting under air conditioner

LG Washing... | 125 views | 0 helpful votes

There's a part under the agitator that lifts off if you pull up from the bottom on both sides) called a coupler that is attached to the shaft with one bolt. The plastic teeth probably have stripped off from this coupler, causing the agitator to not agitate properly.

I would buy the part on amazon.
Here's the link to the exact part:


Video to show how:


GE Washing... | 152 views | 1 helpful votes

FIXYA does not sell parts.

Use the internet to search, or visit retail stores that carry that model to request assistance.

Part number or at least model number is needed to search using Google.com

Possibly available thru Home Depot, Walmart, online at Amazon.com, or www.repairclinic.com


Magic Chef... | 155 views | 1 helpful votes

Steam Store is not loading! Sounds like your problem? Folks you are not the only one to encounter this kind of error. There are many like you facing the same problem and wonder how to resolve the issue. This error is related to gaming and many of the gamers facing the issue.
Devicetricks is the right platform where you can access free tutorials to fix 'Steam Store is not loading' problem. But before that let's have a close insight into the problem first. Keep reading https://www.devicetricks.com/steam-store-not-loading/

Washing Machines | 223 views | 1 helpful votes


Fisher and Paykel washer GWL11 bearing replacement

Take a look at this video to see how to tear down and replace the main bearings in this washer.

on Nov 02, 2019 | Fisher and Paykel GWL11 Top Load...

sounds like it might be time to replace it .

LG Washing... | 104 views | 0 helpful votes


Bosch Washing... | 175 views | 1 helpful votes

There is no 'bE' error code. Could it be 'tE'?

LG Washing... | 52 views | 0 helpful votes

Pull the washer out and tilt it up against the wall. It is always better to look from underneath because the water leak travels downwards.

LG Washing... | 125 views | 0 helpful votes

I suggest you read the operating instructions of your machine. I don't know of such a programme - most programmes include a rinse and spin though there is usually a delicates programme that is a short low temperature wash, leaves the tub full of water (to decrease creasing) until the programmer is advanced and then a short rinse and low speed spin.

Not sure what is special about a special sweater detergent except maybe it is so mild it might behave like soap and contains a fabric conditioner - hence no rinsing. Seems it could be a gimmick...

Best way of washing treasured woollens remains hand washing using soap if possible and rinse with fabric conditioner. Pull into shape while wet and dry flat.

Samsung Washing... | 206 views | 1 helpful votes

You might try replacing the thermistor in the bottom of the outer tub. It's only a $6 part and pretty easy to do. Try cold only wash and see if it works. Also, try putting washer into test mode and run through each segment that it tests. Let us know results by commenting back pls

LG Washing... | 124 views | 1 helpful votes

see this on youtube

Washing Machines | 189 views | 1 helpful votes

If you're talking about the agitator, there may or may not be a nut to hold it on. If not, it simply snaps on and off.

Washing Machines | 173 views | 1 helpful votes

Hi Raymond
Is there power to the appliance?? Do you see any lights?
If the machine is "on" there are a number of possibilities that could stop the machine filling up.
-Have you checked that the water inlet filter is clean?
(Particularly in hard water areas)
- Is there enough water pressure going in?
- Does the machine remains quiet for the time it should be filling then continues to 'wash' as normal but without water or it just stops?
-Disconnet the washing machine from the mains
-Open the machine
-Follow the water inlet hose and the first selenoid you come accross would be the inlet valve (s) assembly
-Check the water inlet valve coil for continuity, it should read several ohms resistance.
If it reads o ohms (short) or it is open circuit no reading at all (blown) the selenoid is faulty and will need to be replaced.
If you have some resistance (1K to 3K ohms) coil is ok
To ensure there is power to the coils, ensure the connecting cable is firmly attached at both ends, at the selenoid end and the controller board end.
-Disconnect the selenoid end and attach an Voltimeter to the wire connector, plug the machine to the mains WITH CARE!! and start a wash cycle. You should get some voltage. If you get nothing for the first few minutes of the cycle, then your controller is faulty and may need repairing / replacing.
Hope this helps and it is only a faulty water inlet valve.

Washing Machines | 120 views | 1 helpful votes

yes go to repair clinic.com type in model number and can get it there and its fast

LG Washing... | 183 views | 1 helpful votes

Not finding what you are looking for?
Washing Machines Logo

258,472 questions posted

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers


Level 3 Expert

85216 Answers

Brad Brown

Level 3 Expert

18121 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides