Washing Machines - Page 2 - Popular Questions, Answers, Tips & Manuals
Add garment light won't go off when Samsung front loader locks. Stops cycle from beginning - Samsung front loader model #WF42H5000AW/A2
Check the Door Latch and Alignment:
Ensure that the door is completely shut and latched. Sometimes, clothing or debris can get caught between the door and the latch, preventing proper closure. Make sure there's nothing obstructing the door.
Inspect the door seal for any damages. A damaged seal might not allow the door to close securely.
Child Lock Feature:
Samsung washers come with a child lock safety feature. If the child lock is engaged, it prevents accidental start of the wash cycle.
Check if the child lock is activated. If so, disable it and try running the wash cycle again.
Motor Control Unit (MCU) Inspection:
Visually inspect the Motor Control Unit (MCU) board for any burned spots. The MCU is located on the left side behind the lower access panel.
If you find burnt spots on the MCU, it might be the cause of the issue. You can order a replacement MCU if needed.
Other Troubleshooting Steps:
Reset the washing machine by unplugging it and then plugging it back in after a few minutes.
If the problem persists, consult a technician to inspect the lock mechanism or control board.
Neff dishwasher tap light flashing -
If your Neff dishwasher is showing a flashing tap light, it typically indicates a water supply issue. Here's a short guide to address the problem:
- Check Water Supply: Ensure the water supply valve under the sink is fully open.
- Filter & Hose: Examine the inlet hose for kinks or bends and the filter at the connection point for blockages.
- Water Pressure: Low water pressure can also trigger this warning. Verify that your home's water pressure is adequate.
If these steps don't resolve the issue, there might be a more complex problem, such as a faulty water inlet valve or a problem with the dishwasher's control system. In such cases, consulting the user manual or contacting Neff customer support for further assistance would be advisable.
What does the code L221 on a H20 Linde mean
The L221 code on a Linde H20 forklift indicates a hydraulic fault, specifically related to the tilt pot.
L: This letter signifies a hydraulic issue.
221: Refers to a faulty tilt pot.
Here are some potential troubleshooting steps to address this issue:
Check the Tilt Pot Connection: Depending on the year of your forklift, the tilt pot's plug might have a poor connection. If it's an older model with a non-waterproof plug, moisture could be affecting it. Try unplugging it and cleaning it thoroughly with electric cleaner.
Inspect Wiring and Linkages: Verify that the wiring is intact and that the linkages are not worn. If everything seems fine, you may need to replace the tilt pot. Keep in mind that recalibration using a laptop might be necessary.
Display Code L221 - Technical Troubleshooting discussion in Forkliftaction's forums
Capacity of a may tag front load model #MHW6000AW0
I don't have real-time access to specific product information, including Maytag front load washing machines. However, I can provide you with some general information. The capacity of a washing machine is typically measured in cubic feet or kilograms and refers to the amount of laundry it can hold in a single load.
GE WASHER MODEL GFWH1200HOWW RUNNING EXTRAAA LONG ON WASH CYCLES??
Hello Heather
Good to see you again.
Also check the small strainers on the water connectors. They can block up with limescale and debris. While the connectors are off, turn on the water into a bucket or a sink. You should have a VERY powerful jet of water. Anything that will reduce flow will lengthen the fill time and therefore to total wash time due to fill and rinses. When it pumps out, also check you have good flow in the drain hose and items can jam in the ridges and catch lint enough to block them almost completely.
One clever thing to do is whilst the water inlet connectors are off, unlock the drain hose, unhook the part that makes the hook, put the round connector in the hose and wrap a tea towel around it. Get someone to turn the water on full bore whilst you are gripping the two hoses together. Run it for a full minute. Water will be flushed into the machine through the pump in reverse. Put everything back and run a rinse and spin with nothing in it, look at all the black lint that is pumped out! I did that once at work and found an apple stalk that had lodged across the ridges of the drain hose which had 90% blocked the pipe.
..
2/19/2024 10:57:30 PM •
GE Washing...
•
28 views • 1 helpful votes
Kenmore filled up with water then quit working?
Question edited for clarity.
'then', a moment in time.
'than', a comparison between one thing and another.
It depends on the model, but usually related to the lid lock. Also check the breaker.
Why does my washer stop working after filling with water?
If the Top Load Washer stops after filling with water, be sure to check the house circuit breaker/fuse as well as the outlet and plug. Washers should be plugged into their own separate, dedicated outlet.
..
Wascomat W655 motor not engaging and final spin pops breaker.
It sounds like you've already tried several troubleshooting steps, but let's see if we can narrow down the issue with your Wascomat W655 commercial washer. Here are some additional things to consider:
Motor Capacitor: The motor capacitor plays a crucial role in starting the motor. If it's faulty, the motor might not engage properly. Consider checking or replacing the motor capacitor.
Motor Wiring: Inspect the wiring connections to the motor. Loose or damaged wires can prevent the motor from functioning correctly. Ensure all connections are secure and free from damage.
Motor Brushes: The motor brushes wear out over time. If they're worn down, the motor won't engage. Check the brushes and replace them if necessary.
Belt Tension: If your washer has a belt-driven motor, ensure that the belt is properly tensioned. A loose or damaged belt can cause motor issues.
Drain Pump: Although you mentioned that the drain pump seems to be working fine, it's still worth verifying. Sometimes a malfunctioning drain pump can affect other components.
Mechanical Obstructions: Inspect the drum and surrounding components for any obstructions. Something lodged in the drum or motor assembly could prevent movement.
High-Speed Spin: Since the issue occurs during the high-speed spin, focus on components related to this phase. It could be related to the motor, belt, or even the drum balance.
A professional technician could perform more advanced diagnostics.
If you haven't already, you might find it helpful to consult the diagrams and manuals specific to the Wascomat W655 washer. Alliance Laundry Systems provides replacement parts and repair resources.
Diagrams, Parts and Manuals for Wascomat W655 Washer (alliancelaundry.com)
Why does my water won't stop filling?
A few possible causes:
Blocked Water Level Switch: Most top-loading washing machines utilize a pressure switch to tell the water when to shut off during a wash or rinse cycle. If the tube becomes blocked with minerals from hard water or if the switch itself goes bad, the water will never shut off.
Bad Water Valve: Valves at the points where the hot and cold water hoses enter your washing machine control the flow of water into the machine. If these valves become stuck open, or if their seals become lost or compromised, the water will continue to flow into the machine.
Faulty Controls: The controls might fail to acknowledge the input from the pressure switch and never advance from one cycle to another. In some cases, this is a voltage problem, while in other cases the controls themselves are bad and would need to be replaced.
If you've already cleaned and cut the ends of the tube going to the level sensor and the issue persists, it might be best to consult with a professional appliance repair service. They can help diagnose and fix the problem accurately. Please remember to turn off the water supply and unplug the machine before attempting any repairs.
Kenmore washer 110.20022013 stops after wash cycle
Usually it's the lid switch..When you open the lip look straight down usually..When you close the lid it inserts a small plastic piece that goes into the hole telling the washer the lids down..If it broke it will make the washer stop mid cycle..You can stick a wooden (only made of wood) into the hole and sometimes it will start to work..Then you know that's the problem and just get your model number of the washer and replace it..Hope this helps
Not finding what you are looking for?