Cardiozone Exercise & Fitness - Answered Questions & Fixed Issues

Hello again Having typed everything below the dotted lines for the last 30 minutes, I found this. It has a magnetic speed sensor on the pulley https://www.justanswer.com/fitness-equipment/2srkz-just-moved-cardiozone-elite-max-hr-treadmill.html ============================================== Here is the parts diagram and it shows no speed sensor and all parts are unavailable. https://www.fitnessrepairparts.com/equipment/Select/7631/CardioZone/CZE-Elite-Plus-HRT Parts Diagram closeup https://www.fitnessrepairparts.com/equipment/7631/diagrams/7403 That is contradicted here, but my view is that they are guessing because the parts diagram shows no sensor and if it was there and a part of the management system and expected to fail, it would be. There is a picture of of two sensors from Amazon and eBay, one is a Hall Effect Sensor, and the other is a Magnetic sensor. If it has them, you wouldn't be able to miss them and they would be connected to Part 17 - Controller. https://www.google.com/search?q=cardiozone+elite+plus+hr+t+treadmill+sensor+replacement Generic Treadmill Sensors Treadmill RPM Speed Sensor - Replacement for Pacemaster Bronze, Pro, Plus, Plus 2, Elite, & Select Treadmill $21.14 Amazon CA High Quality Treadmill Magnetic Sensor Speed Sensor For Running $12.89 eBay Free shipping ..

Try pressing the Mode button again until the error message goes, or disconnect from the mains or remove batteries to reset. How do I fix E7 error on treadmill? E6 or E7

1. Turn the power OFF, wait 5-seconds and turn back ON.
2. Get into test mode and enter through the I/O testing step. ...
3. Once the unit is in the mid-level position, power the treadmill off for 5-seconds and then power it back ON.
4. Start the treadmill.

https://www.google.com/search?q=cardiozone+treadmill+e7+error

Use a non alcohol based silicon spray or liquid. The WD40 brand make the 3 in 1 silicone spray and it’s good for all non waxed running belts. Just make sure you get the spray in the middle of the belt. (Underneath of course) watch a YouTube video if unsure.

Nice blog. Thanks for sharing this valuable information. <a href="https://sportsindeed.com/excercise-fitness/treadmills.html">Treadmill Dealer in Chandigarh</a> <a href="https://sportsindeed.com/excercise-fitness/treadmills.html">Treadmill Dealer in Mohali</a> <a href="https://sportsindeed.com/excercise-fitness/treadmills.html">Treadmill Dealer in Panchkula</a> <a href="https://sportsindeed.com/excercise-fitness/treadmills.html">Buy Treadmill in Chandigarh</a>

1st take side rails off front hood .you have afront roller and a back roller. for the front take out the two or one bolts holding the the roller in placenow the back roller take out the bolts that hold the roller in place . now on the deck there is 3or 4 screwson each side holding the deck in place. slide w/ belt off put on new deck.install screws, rollers ,bolts.. now center w/belt and adjust tention on w/belt

Your controller is shot. Replace your controller

This could be cused by the the display cover you touch to control the functions pressing on the touch switch array just under it. Carefully remove this. it is held on by adhesive and see if the symptom goes away. If it does, look for any dents on the cover. I have worked with these type of switches for nearly 20 years and they can be problematic. The other possibility is the mechanical switches you use to increase/decrease speed or tilt. They plug in seperately and you can disconnect them to see if they are causing the problem.

This usually means a faulty LCB or motor.The fact it has not been used much doesn't matter. It is 7 years old. Usually you can not see faulty parts on the LCB. I do think if you really want the answer call a treadmill repairer . If you don't know what you are doing it can be dangerous.

replace the old batteries and clean the contacts with c. cleaner2) tight and clean the ribbon cables insides.3) tight the upper and lower connection , and clean4) Adjust the Reed SWITCH, see the diagram attached.God bless you

see the video and proceed according. God bless you2) LUBE the rollers bearings too3) test the drive belt motor, and replace it4) Test the input voltage motor, if there are the motor need repair, see my personal TIPS for help5) Test the output voltage board, for input voltage motor, if there are NOT THE board is faulty. see the block d.God bless you

buy it from www. fitnessrepairparts.comGod bless you

Lets eliminate the motor first, unplug unit remove motor shroud fin the 2 leads from motor to lower board. Connect a 18v DC battery to the leads this start the motor to move at approx. 1 mph if it does motor is good,if not you may worn motor brushes worst case open connection in the motor.
Now if the motor is good then reconnection the leads and plug in unit the lower board should have some LEDs lit up. Now find the LED that says PWM start unit if that light should start to flicker then the upper board and wire harness are work properly. Turn off the treadmill then turn it on and with a multi meter insert the leads into the connectors that go to the motor, then put the meter on 200v DC then start the treadmill you should get a reading 5 to 10v DC if you get 0v DC then the board will need replacing

Dear Sir:The best way is to go to the company, and they can resolve your problem.Otherwise you will be lose your time. Remember the factory has many options with the manufacturer of the screen, and gave the o.k for your equipment. sincerely

Watch the videos:http://www.youtube.com/watch?v=TquYcOzGIw4&feature=relatedhttp://www.youtube.com/watch?v=9G4MZh8JO2Qhttp://www.youtube.com/watch?v=M7qJrRbdfBchttp://www.youtube.com/watch?v=MIIxoPtvhy8hthttp://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnesshttp://www.youtube.com/watch?v=bF3OyQ3HwfU&feature=relatedSome equipment has board for relais. Test if the relais for Down and Up and closing and open. and cleand contact with special spray contact cleaner (radio schack or computer store). Finally see some loose connections or wires.SEE the block diagram, and now you will have strong resultant for to determine what is faulty. Look how the main motor has the90% aprox functions in any treadmills. sincerely.Good luck.E.CUADRAMANAGUA, NICARAGUA. CA.

If the console takesbatteries, replace them. If this does not work or your console does not requirebatteries, check the reed switch or optic sensor. Reed Switch:Unplug the treadmill and remove the motor hood cover. The reed switch is mountedon the frame next to the front roller pulley. There is a magnet glued into thefront roller pulley. When adjusting the reed switch, make sure it is pointingdirectly at the magnet. Move the tip of the reed switch within 1/8" of themagnet. Also, check to see that the wire is not damaged, and is connected tothe console. 2nd Step: tight the keypanel vs Display board and clean with contact cleaner spray . Tight the connector from Display Board vs Main Motor Board. See the block diagram how the main motor board has aprox 90% functions in any treadmill. Good luck, Now you will strong resultant in determine what is faulty.

Removethe bolts or screws securing the console to the upright assembly. Lift theconsole and confirm that the cable connections are secure. Remove the coverfrom the console's battery bay and install a fresh set of batteries. Replacethe battery cover.2Detachthe ends of the pedals from the crank axles. Remove the left and right discshields and side shields. Inspect the interior of the base unit and locate theflywheel.3Inspectthe flywheel as it turns. Locate the magnet installed on the flywheel. Turn theflywheel until the magnet passes in front of the nearby reed switch. Loosen thescrew securing the switch in place. Rotate the switch to reduce the gap betweenit and the magnet. Tighten the screw.4Replacethe left and right disc shields and side shields. Reattach the ends of thepedals to the crank axles.Good luck, sincerely.

GO TO AMAZON.www.amazon.com ( look for Lube-N-Walk Treadmill lubrication kit us$11,58 and buy it.Do this with the Videos:http://www.youtube.com/watch?NR=1&v=USSgbsZbDLQhttp://www.youtube.com/watch?v=hKbAqvuOBS0&feature=relatedhttp://www.youtube.com/watch?NR=1&v=KiEZDNe0F8Qhttp://www.youtube.com/watch?v=wjrVjYe2LYQ&feature=relatedhttp://www.youtube.com/watch?v=CuMjcPLYehw&feature=relatedhttp://www.youtube.com/watch?v=yX_0vRPdMfU&feature=relatedhttp://www.youtube.com/watch?v=zXeHMWTcLUY&feature=relatedhttp://www.youtube.com/watch?v=dxpOOPetVLoGood luck, sincerely. G-d bless you.E.CUADRAMANAGUA, NICARAGUA.

Dear Sir:

I will help you.

Please in all this check in, use The Vom digital:
1. NoPower
o 1 Make sure that the surge protector being used isproperly grounded and turned on. Check that the treadmill power cord isproperly plugged into the surge protector. o 2 Check to see that the key is inserted in theconsole. o 3 Check the circuit breaker on the frame near thepower cord. If the reset/off circuit breaker has tripped, wait 5 minutes andthen reset the breaker by pressing the switch in.
4)Check the circuit breaker from the main panel( wall) and Measure the Voltage for properly 115VAC. if there .
Hoping help you, contac me if there are something extra.
blessing.
E.CUADRA Managua, Nicaragua.C.A.

the console first and then the uprites that hold the console. that should be enough

Your problem might be that a magnet has fallen off. Here's an illustrated guide which should make fixing it easy: http://fixmytreadmill.blogspot.com/2010/10/how-to-fix-treadmill-e1-error.html

Good luck.