Casio Office Equipment & Supplies - Recent Questions, Troubleshooting & Support
My screen says DEC 0
Your calculator is in binary mode. Press MODE 1 to switch to "normal" mode or MODE 2 to switch to complex mode.
How do you get a
Some keys have a letter of the alphabet next to them. The letters are A, B,C,D, M, X, Y. They correspond to memory registers (memory locations) in which you can store values.
To enter a letter as when you are entering an expression with variables, you press the [ALPHA] key followed by the key next to which is the letter you seek. To enter letter A, You press [SHIFT] [(-)] if I am not mistaken.
Oi como faco para tira
Wale Sarumi KomputerSolu??o
jullymarrodr says:
Ol?, como fa?o para remover a letra E que aparece na tela da calculadora quando coloco no modo impress?o, ? uma calculadora casio hr100mt
2/8/2024 12:24:27 PM •
Casio...
•
Answered
on Feb 08, 2024
My casio KL-60 Power ON got message ERROR!. How to clear the problem
Here are some steps you can try to clear the problem:
- Check the Label Tape: Ensure that the label tape is properly installed and correctly aligned in the label printer. Sometimes, an improperly installed label tape can trigger an error message.
- Check for Paper Jams: Open the label printer and check for any paper jams or obstructions that might be causing the error. Clear any jams or obstructions you find.
- Replace the Batteries or Use AC Power: If your Casio KL-60 label printer is powered by batteries, try replacing the batteries with fresh ones. If you're using AC power, make sure the power adapter is working correctly and properly connected.
- Perform a Soft Reset: Turn off the label printer and unplug it from the power source (if applicable). Wait for a few seconds, then plug it back in and power it on again. This can sometimes resolve temporary issues.
- Check the User Manual: Consult the user manual or troubleshooting guide that came with your Casio KL-60 label printer. It may have specific instructions for troubleshooting error messages.
- Factory Reset: If the error persists and you have tried all other steps, you may need to perform a factory reset to restore the printer to its default settings. Keep in mind that a factory reset will erase any custom settings you may have made.
How do i do prime numbers on the NEWYES NY-991MS calculator and CTIFREE fx-991ES PLUS calculator?
The NEWYES NY-991MS and CTIFREE fx-991ES PLUS calculators do not have a dedicated "FACT" button like the Casio FX-83GTX. However, you can still find prime numbers on these calculators.To find prime numbers:NEWYES NY-991MS:Press the "MODE" button.Choose "PRIME" from the list of options.Enter the desired number and press "=" to check if it's prime.CTIFREE fx-991ES PLUS:Press the "MODE" button.Select "TABLE" or "TABLESET."Input a starting point and an ending point, then observe the table for prime numbers.Although the techniques may vary from those used on the Casio FX-83GTX, they prove to be effective for prime number calculations on the designated calculators.
Where is the factorial (!)
There is no button but a menu tab.
In Run screen, enter the number whose factorial you want to calculate ( number can be at most equal to 69), press [OPTN][F6] to get to next page pf menus. Press then [F3](PROB) then [F1] (x!) followed by [EXE].
11/20/2023 11:52:11 PM •
Casio...
•
Answered
on Nov 20, 2023
How to change tax rate on Casio MS120TV
I found the solution listed against a different CAsio Calculator.
It was .. Press AC, then hold 'set' for a few seconds then press 'Tax+' , input new tax rate then press 'set'. Job Done
10/28/2023 1:24:54 PM •
Casio...
•
Answered
on Oct 28, 2023
Not finding what you are looking for?