Cisco Computers & Internet - Page 9 - Recent Questions, Troubleshooting & Support
Problem with cisco 2513 routers
Check what version of software do you have. Do "dir" command and look at the file name. If it contains "K9" in the name, then it has "crypto" functionality, if it doesn't, then you need to find it (however it will be quite a challenge, as these routers are end-of-life for a decade...)
Good luck,
Mike ' CCNP, CCDP, CCSP, CCVP, etc.
Cisco Compatible Headset Adapters for 7940 7960 etc
I have added cisco 7916
I know it may be late (definitely late), but have you defined in the CallManager, that your phone has a "side card"? If CallManager does not know that it has to push an additional firmware to a particular phone, it will not work.
Good luck,
Mike ' CCNP, CCVP, CCSP, CCDP, MCSE, etc.
Headset Adapter Co.
Headset Adapters for office phone system
Slow internet speed behind cisco router
Greatings !I put WORKGROUP within the domain name field of the Network tab.Speedtest moved from 10Mb to 100Mb that is the maximum speed provided by my cableBox (Numericable).Very goodThanks a lot to Kasper Mikkelsen
I am in college online @ NAU, and I'm only in my
We can answer specific questions for you as long as you are specific. Broad questions are difficult to answer in a reasonable amount of time but if you ask us to explain database normalization, that can be handled in a reasonable amount of time.
When you graduate, you will likely get a job with a smaller company. This is simply because there are more of them then larger companies. Smaller companies mean smaller networks which means less work so they will not be able to keep you busy working only on the network. The solution is to either hire somebody part-time or to hire somebody with a related talent that they need. That is where the DB knowledge comes in handy.
!!! WARNING: The switch is not usable !!! 3560-24PS
There is a possibility of IOSĀ® corruption, so better check on that before using warranty, RMA or dumpster/recycling
Error Message SW_VLAN-4-IFS_FAILURE: VLAN manager encountered file operation error: call = [chars] / code = [dec] ([chars]) / bytes transferred = [dec].
Explanation This message means that the VLAN manager received an unexpected error return from an IOS file system (IFS) call while reading the VLAN database. The first [chars] is the IFS operation that failed. The first [dec] is the error code, the second [chars] is the textual interpretation of the error code, and the second [dec] is the number of bytes transferred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
CISCO 6248 beep sound
Beep Codes Cause (Depending on RAID Level)
3 seconds on, 1 second off
- RAID 0: One or more drives offline.
- RAID 1: Two drives offline.
- RAID 5: Two or more drives offline.
- RAID 6: More than two drives offline
1 second on, 1 second off
- RAID 1: A mirrored drive failed.
- RAID 5: One drive failed.
- RAID 6: One or two drives failed.
1 second on, 3 seconds off
A hot spare drive has completed the rebuild process and has been brought into the array.
Cisco 7942 factory reset
When performing the factory reset procedure we are about to describe, it is important to keep in mind that the IP phone will lose all configuration files and phone applications. This means that it is necessary to have CallManager or CallManager Express setup so that the IP phone will be able to receive the new information (phone application and configuration) after the reset procedure is complete, otherwise it is most likely that the IP phone will not be usable until this information is loaded on to it.
This preparation also happens to be the procedure for upgrading a Cisco IP phone firmware.
Follow the steps below to successfully factory reset your Cisco 7942, 7962 IP phone:
- Unplug the power cable from the phone and then plug it back in. The phone begins its power up cycle.
- While the phone is powering up, and before the Speaker button flashes on and off, press and hold #. Continue to hold # until each line button flashes on and off in sequence in amber.
- Release # and press 123456789*0#.
You can press a key twice in a row, but if you press the keys out of sequence, the factory reset will not take place.
After you press these keys, the line buttons on the phone flash red and the phone goes through the factory reset process.
Do not power down the phone until it completes the factory reset process and the main screen appears.
My Cisco IP Phone 7945G keeps rebooting after I did a factory reset. Is there a way to fix this?
According to Cisco, when initiating a
factory reset procedure certain information from the IP phone is
erased while other information is reset to the factory default value, as shown in the list below:
Information Erased:
- CTL File (Certificate Trust List)
- LSC File (Locally Significant Certificate)
- IP Phone Call History (Calls Received, Placed, Missed etc)
- Phone application
Information Reset to Default:
- User configuration settings (ring tone, screen brightness, sound levels etc)
- Network configuration settings
t is highly advisable to follow the firmware upgrade procedure in a non-working environment to ensure other phones are not affected (in case of an accidental reboot), and to avoid the freshly factory reset ip phones obtaining the working environment's settings.
Please use the link below and follow the instruction
http://www.firewall.cx/downloads/cisco-tools-a-applications/cisco-ip-phone-a-ata-firmware-downloads.html
Not finding what you are looking for?