Conia Washing Machines - Page 9 - Recent Questions, Troubleshooting & Support

See page 89 (Error Messages) of this manual. It will help you. Girbau HS-4022 Manuals ' ManualsLib

see if power to motor if yes bad motor if no possible board

Problem I found ,was a colour sheet had got in drain hose and in encircled the ball in hose blocking hose .removed hose cleaned , refitted and machine working again

Should the light on your device's lid unlocking feature keep flashing, there might be a problem with the locking mechanism. For troubleshooting instructions or additional support, consult the user manual or get in touch with customer service.

Water must come from somewhere. Some doors contain water because the weep hole is clogged. Do your doors have drain plugs and what happens when you pull those on the driver side out?

Help and videos here, but it isn't a known make in Canada. https://www.google.com/search?q=brada+top+loader+washing+machine+agitator+came+off ..

Pull the mains plug out, wait 15 minutes and plug it back in. Reset done..

Check the Motor and Drum: Sometimes, issues with the motor or drum can trigger the F-11 error. Inspect the motor and drum for obstructions or mechanical problems. It's possible that something is impeding their movement.Verify Water Supply: Ensure that there is no issue with the water supply. If the washer doesn't fill properly during the spin cycle, it can lead to an error code. Check for water inlet valve problems or water pressure issues.Verify Electrical Connections: Double-check all electrical connections and wiring, not just those accessible from the bottom panel. Issues with the control board or other components may not always be visible from the outside.Sensor and Switch Inspection: Look for any faulty sensors, switches, or pressure switches that might affect the spin cycle. A malfunctioning sensor or switch can lead to the error code.Professional Service: If you've thoroughly checked the visible components and the problem persists, it's advisable to contact a professional appliance technician who can perform a comprehensive diagnostic and identify the root cause of the issue. They may need to use specialized diagnostic tools to pinpoint the problem accurately.The F-11 error code can sometimes be challenging to diagnose because it can result from various underlying issues. If you've exhausted your troubleshooting options and the problem persists, professional service is likely the most effective way to address the issue and get your washer back in working order.

check drain hose for blockage if ok check pump

All questions need 'make model (what it is)' and you only have 1/3. E3 is water too high or too low, or hot water related not hot enough or vibration depending on maker. Error message E3 in integrated compact dishwasher indicates too much inlet water and/or a leak. Oct 7, 2019

Compact dishwasher displays error message E3 - Electrolux

Visit the following link LG WFT6500 Product Support :Manuals, Warranty & More ' LG Sri Lanka See the troubleshooting section. It will help to pinpoint the issue.

Although redistributing the clothes might be the easy answer, you have have broken suspension strings or a failed shock absorber. The only way to check is to remove the case.

If your Defy Electrologic washing machine is filling and releasing water at the same time, it is likely that the drain hose is clogged or the drain pump is defective. Check the drain hose for any clogs or debris and ensure it is clean. If the drain hose is clear, the problem could be a defective drain pump. In this case, the pump will need to be replaced.

Failed Water Inlet Valve on your unknown washing machine. https://www.google.com/search?q=Water+Inlet+Valve ..

The pump and hoses would not cause that issue. The most likely reason is that the rotary dial and timer / contacts are failing. If you can get in behind it and spray some electrical switch cleaner into it, it might get you a few more months of service.

Check screens in hoses and valve for debris. If they are clear, replace valve.

Repairing the electric cable on a vacuum sealer can be a bit tricky and potentially dangerous if not done correctly, so if you're not confident in your ability to do this safely, it's best to consult a professional or consider replacing the vacuum sealer. However, if you have some experience with electrical repairs and feel comfortable tackling the job, here are some general steps to guide you: **Note:** Ensure your vacuum sealer is unplugged from the power source before attempting any repairs. 1. **Gather your tools and materials:** - Screwdrivers (typically Phillips and flat-head) - Wire strippers - Heat shrink tubing or electrical tape - Wire connectors - Replacement cable (if needed) - Multimeter (for testing) 2. **Identify the issue:** Carefully examine the electric cable to determine the exact problem. If there's visible damage to the cable, such as cuts or exposed wires, you'll likely need to replace the damaged section or the entire cable. 3. **Cut and strip the cable:** If you're replacing a section of the cable, cut it where the damage is, and then use wire strippers to remove a small portion of the insulation from the ends of the wires. Make sure to cut cleanly without damaging the wire strands inside. 4. **Prepare the replacement cable:** If you're using a replacement cable, strip the ends of the new cable to expose the wire ends. 5. **Connect the wires:** If you're replacing a section of the cable, connect the wires from the new cable to the wires from the old cable. Use wire connectors to secure the connections. If you're working with a whole new cable, you'll need to connect it to the vacuum sealer's internal wiring. Make sure to connect the wires with the same color-coding as the original cable. Usually, it's black to black and white to white, but check the manufacturer's instructions. 6. **Insulate the connections:** After connecting the wires, insulate them properly to prevent any electrical hazards. You can use heat shrink tubing or electrical tape to cover the exposed connections. If using heat shrink tubing, heat it with a heat gun to shrink it tightly around the wires. 7. **Test the vacuum sealer:** Before fully reassembling the vacuum sealer, plug it in and test it to ensure it's working correctly. Make sure there are no exposed wires or loose connections. If the vacuum sealer functions as it should, proceed to the next step. 8. **Reassemble the vacuum sealer:** Put the vacuum sealer back together, securing any panels or covers that you removed during the repair. 9. **Final safety check:** Double-check that everything is securely connected, insulated, and safe. Ensure there are no exposed wires or loose components. 10. **Plug in and use with caution:** Once you're confident in your repair job, you can plug in the vacuum sealer and use it. Always exercise caution when working with electrical appliances, and if you have any doubts about your repair skills, consider seeking professional assistance. Your safety is paramount. If you're not comfortable with these steps or if your vacuum sealer is still under warranty, consider contacting the manufacturer or an authorized service center for repairs or advice.

have you cleaned vent line should be 4 inch ducting, if using plastic flex vent line remove it and clean it. If venting into interior wall removedryer and clean out wall cavity.

Error code E1 on Fisher & Paykel SleepStyle 200 CPAP machine indicates a power supply issue . To resolve this issue, you can try unplugging the machine, waiting for 30-60 seconds, and then plugging it back in. This may reset the machine and resolve the error. If the error persists, you should contact your healthcare provider for further instructions .

Error 019