Danby Refrigerators - Popular Questions, Answers, Tips & Manuals

The two lines entering/exiting the lower right of the attached photo (back view) should be the condenser as the lines on left side appear to be for evaporation. Looks like they buried the coils inside the right side panel and possibly the top. The coils may be bonded to panel metal and the metal is what radiates extracted heat.

No it is time for a new one. There is either a leak on the inner liner or the insulation between the inner layer and outer layer has broken down and is causing condensation.

Question edited for a lot more clarity. Amazon, Walmart or Danby direct. https://www.google.com/search?q=danby+dkc146sldb+ptc+relay+replacement ..

If your Danby DBC514BLS-1 beverage fridge is not cooling and you have noticed frost on the back coil, it could be a sign of a problem with the fridge's defrost system. Here are some steps you can try to troubleshoot the issue:

1. Check the fan to see if it is running. If the fan is not running, it may be a problem with the fan motor or the control board.
2. Check the defrost timer and thermostat. The defrost timer controls the defrost cycle, and the thermostat monitors the temperature inside the fridge. If either of these components is faulty, it could cause the fridge to frost up.
3. Check the wiring and connections. Make sure all the wires are securely connected and that there are no loose or frayed wires.

it is possible to replace the fan in your model of fridge, If you decide to attempt the repair yourself, you will need to purchase the correct replacement fan for your fridge and have the necessary tools to make the repair.

Increase the temperature inside by turning the knob anticlockwise. Put a thermometer in the fridge, it should be 3 or 4 degrees Centigrade. https://www.google.com/search?q=Danby+fridge+model+DFF100C2BSSDD+too+cold ..

The power switches for a Danby Beverage Center Model DBC514BLS-1 are the power on/off switch and the temperature control switch. The power on/off switch turns the unit on or off and the temperature control switch allows you to adjust the temperature of the beverage center.

The door sensor on the DFF 477 fridge is located behind the main control panel located inside the refrigerator. To check for the presence of the door sensor, you will need to remove the main control panel and inspect the wiring behind it.

Propane is flamable but not Ozone damaging. Usually they are foilled with Cyclopentane, that is part of the Propane family but any refrigeration engineer will know what to do, if not look it up in the many training manuals.

Yes it has a fan you should here it and feel it. It sounds like your defrost coil may have gone out. Take the back pannel of the freezer off and see if it is clogged with frost.

Question edited to toss in some caps. Question moved to model category. It could be many things but refrigerator repair is not a DIY home job. The first thing to check is that is has enough refrigerant gas and you can't do that. https://www.google.com/search?q=Danby+DWC612BLP+not+cooling ..

Turn the dial and make it a little warmer. It should be 4'C to 6'C. It is possible it needs a new thermostat if it is running all the time.

E2: Freezer temperature sensor failure. E5: Freezer defrosting sensor failure. E6: Communication failure. E7: Ambient temperature sensor failure.

Troubleshooting - Danby DUF138E1WDD Owner's Use And ...

check cooling if not covered with dust check inside with thermometer if ok bad temp sensor if warm possible low on freon or bad compressor

possible bad control board

Probably it has leaked the coolant.

Looks like you have freon leak

Item doesn't exist https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk02FERmt_ToyHzluH98CNxyjKdhijA%3A1609266317875&ei=jXTrX8PpNMHNtQboiqSgDQ&q=Danby+DCR+100WE ..

Guessing here, Bad thermostat would affect both sides, not just half. I would look for a door or damper door, an obstruction in the air path between the two, where the inside fan lives and on down to the other side if defrosting does not show any difference after plugging it back in a day or two later. If it shows a difference, then there is a defrost problem, deftost cycle not working.

CHECK WITH DANBY