Electrolux Washing Machines - Page 8 - Recent Questions, Troubleshooting & Support

Hello, I think that your drain pump is blocked of is faulty. You will need to drain the water from the machine, remove the drain hose from the drain outtlet on the wall. or sink unit. Once you have done this check that the pump filter ( if fitted) that it has not clogged with fluff or other debris, If that is not clogged, you will need to look under the machine and check the hoses from the drum to the pump for items like flimsy underwear, socks, or other small items, these can slow the water flow, stop it, or stop the impellor on the water pump. If that is not blocked. check that the drain hose to the domestic outlet is not blocked, as sometimes if you live in a hard water area, it can block with calcium deposits. I hope this helps?

10E: Water level is above parameter set (10 scale units) after water discharge

If you can get to the drain hose and hold it low down, the water should come out allowing you to get to the clothes. Be careful where the water goes though.

Disconnect power supply. Remove top panel. Now is door lock accessible. Open door, remove door gasket from housing (not from tub), remove two screws and replace door lock. Dado

The EH0 error indicates a problem with the incoming voltage or the power supply or wiring inside the dryer. If there has been a problem with the electricity coming into your home (brown out or similar), the error will resolve when the power company fixes the issue. Otherwise the control board is not receiving the expected power from the power supply. First unplug the dryer or shut off the power at the circuit breaker. Unplugging the dryer for at least 30 seconds will reset the error message. If you can, plug another appliance into the outlet and check if that works. If there is a wiring fault, get an electrician to check the outlet and wiring. If the problem is inside the dryer, the power supply, the control board and the wiring to the control board will need to be checked. There could be a loose wire, a broken wire or a spot where the insulation has been damaged and two wires are touching. Check all of the wiring harnesses where groups of wires plug into the control board. Replace or fix any damaged parts or wires. The parts diagrams are available here: https://www.ransomspares.co.uk/parts/brands/electrolux/tumble-dryers/edc2086glw%20(91609724100)/ . If the dryer is under warranty, contact Electrolux to have the unit serviced. I hope this helps. Cindy Wells

possibly could have motor bearings going out

5.5 Opening The Door (from user manual) While a program or the 'Delay Start' is operating, the appliance door is locked and the display shows the indicator 'key symbol '. First set the machine to PAUSE by pressing the "Start/Pause" touchpad. Wait until the door lock indicator 'the key symbol ' goes off, then the door can be opened. If the door lock indicator 'the key symbol ' does not disappear, this means that the machine is already heating and the water level is above the bottom edge of the door or the drum is turning. In this case the door CAN NOT be opened. If you can not open the door but you need to open it you have to switch the machine off by turn the program selector knob to the position " 0 " to deactivate the appliance. After about 5 minutes the door can be opened. CAUTION ! Pay attention to the water level and water temperature. Dado

Thank you for your post, Glen Wagner! In order to get proper replacement parts for your Electrolux washer you would need to have the model number available. I would recommend reaching out to the manufacturer, to guarantee the parts are correct. If you need assistance with installing the parts you may want to consult a professional for proper installation of replacement components. I hope this information has been beneficial. -Matt

1) It could be that the washing machine drum has collected greasy residue from previous loads. Try cleaning the drum by running an empty cycle with a cupful of white vinegar. 2) Or could be the bearings. When bearings are on the way out they leave streaky dark marks on the clothes.

Hello sreenivasulu, if you are receiving error code E30, first check if it is a false error code by resetting the power to the appliance by either unplugging it or flipping off the breaker for about 30 seconds. If the error code persists, it could potentially mean a number of things: a pressure sensor issue, defective wiring, valve assembly problem and/or control board issue. I would strongly recommend connecting with an expert technician to assist further.

Get warranty service if new.

The EHO (or EH0) error indicates a problem with the incoming power or an electrical problem inside the washer. Unplug the washer for a while to reset the error code. Next check your wiring and make sure that the outlet doesn't have a fault. If you live in an area with brown-outs or wires that touched during a storm, wait until the electricity is repaired. Then check if the power supply to the washer was damaged by the surge or changing power levels. If these aren't responsible for the problem, you'll need to check the wiring for shielding damage, the wire harnesses and the rest of the washer. There is a parts diagram here: http://docplayer.net/60693214-Spare-parts-list-household-washing-machines-pnc-elc-brand-model-market-electrolux-ewf10842-th-washing-machines-front-loaded.html . I hope this helps. Cindy Wells

https://www.electrolux.com.sg/globalassets/5-support/manuals/en-sg/ewt903xs-troubleshooting-guide-en-sg.pdf

Bad motor most likely. Will it come back on after cooling down?

It is the customer fault code. Simply turn on and turn off appliance. E11 - problem with fill water E21 - problem with draining water E41 - door open All other errors require service staff !!!

The door of the washing machine cannot be opened here.3. Perform emergency door opening On some machines the door can be opened in an emergency by pulling down on a bar using a screwdriver or similar object, for example. If the machine has an emergency release, it is located next to the fluff filter. See the full description in the user manual. Note: Make sure that the water level inside the drum is not too high. If necessary, proceed with an emergency drain.

Warning: Risk of burns! Make sure that the water temperature is not too high and the laundry is not hot. If necessary, wait until they cool down.

Warning: Risk of injury! Make sure that the drum is not rotating. If necessary, wait until the drum stops rotating.

4. Reset the machine Switch off the power to the machine and then switch it on again after about 20-30 seconds. Then test whether the machine is working normally. 5. Contact an Authorized Service Centre If the door cannot be opened without water in the machine and the above advices do not resolve the problem, we recommend requesting a visit by a service engineer.

NOTE: Depending on the problem, you may be charged for a service visit by an engineer, even during the warranty period.

Warning: We do not recommend using the product until the problem has been completely fixed. Unplug the product and do not plug it in again until you are certain that it is OK to do so

which light is flashing & what colour it is e.g (Start, End, door open, etc.)

water leaking means a gasket is needing to be replaced.

6.1 Child lock function This option prevents children to play with the appliance while a programme operates. The programme knob and the touchpads are locked. Only the on/off button is unlocked. Activating the child lock option 1. Press the on/off button to activate the appliance. 2. Press and hold touchpads (A) and (D) at the same time until the child lock indicator comes on. • It is possible to deactivate the child lock option while a programme operates. Press and hold the same touchpads until the child lock indicator goes off. Dado

Family error code E10 is visible to customers and (could be E11 and E13 only visible in service mode) means problem with filling water. I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. during the execution of the washing programme). Press and hold down START/PAUSE and the nearest option buttons for at least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to the last alarm. The alarm sequence continues as long as the two buttons are held down. Before anything first check filter on solenoid valve and filter on inlet hose. Also, check is there any water inside drum, means that last drain phase is finished and pressure switch is in empty position. E11 - Tap closed or water pressure insufficient; Drain hose incorrectly positioned; Water fill solenoid faulty; Leaks from pressure switch hydraulic circuit; Pressure switch faulty; Wiring faulty; Circuit board faulty¸. E13 - Drain hose incorrectly positioned; Water pressure insufficient; Water fill solenoid faulty; Leaks or blockage in pressure switch hydraulic circuit; Pressure switch faulty; Circuit board faulty. Dado