Epson Stylus - Recent Questions, Troubleshooting & Support - Page 7
Paper jam error
Dear Sir,
I have Epson Stylus-1390 Photo Printer. Problem is when giving photo
printing option thru printer driver printer get error is paper jam..
can you give me solution for the same.
thanks
How do i connect my epsonR300inkjet printer wirelessly
Network printing with a non-networked printerThis model printer has only an USB printer connection andnormally connected to a computer or laptop.To connect this printer wirelessly to all laptops on your wireless networkthere are a couple of methods.Connect the printer to a desktop computer and setup the printer as a sharedprinter. Next connect the desktop computer to your wireless router with a LANcable and then configure the wireless laptops to connect to the shared printeron the desktop computer. NOTE - This desktop computer and printer must be on atall times for the wireless laptops to print to the printer.OTHER METHODConnect the printer to an USB print server and connect the print server to thewireless router with a LAN cable. The printer drivers needs to be installed onall the wireless laptops and then the printer port needs to be deleted from theUSB port and a new IP address printer port installed. This IP address will bethe IP address of the print server.
CANON PIXMA IP1200 resetting
My converted iP1200 is currently blinking green, yellow, green, yellow on the power lights after start up and print request. The pop-up prompt suggests turning off the printer and turning it back on. Error 5100 is always seen.
Please Help Me...
rakibfuture
Epson stylus cx 7400
Epson includes step-by-step instructions on changing the ink cartridges in the Printing Preferences menu:
Click the start button and open the Control Panel.
Right click Printers and select Printing Preferences.
Click the Maintenance tab.
You should see a button that says Ink Cartridge Replacement.
Just follow the instructions and it walks you through it.
Urgent: red light error on Epson Stylus CX3650
It appears that this is an overseas model (at least for those here in the US that is) as far as I can tell. This will use the same drivers as the CX3600 model though. Depending on how long you have had this and how often you use it, you may have a waste ink reset situation. While I have not had any personal experience with this model, there are several references on the internet on how to do a reset. There is even an "SSC Service Utility" you can search for that lists this printer as being supported. It cannot reset the ink counters but it may reset the waste.
Good luck, I hope this is of some help.
How to download epson adjustment program
On most Epson printers the Adjustment program can be accessed via the printers interface, without need to do it via a pc. Without knowing the model it is fairly difficult to answer this question more fully. However if you have a manual or can download the manual from epson.com, there will be a chapter on manual head cleaning and adjustment proceedures.
Epson cx5500
I need some software for resetting epson cx 5500, please ?
Print Cartridge Problem- HP PSC 1513
which cartridge is giving you problems? The one on the right? I think that is, IIRC, the black ink. Is it out of ink? If so, go to OfficeMax or Walgreens and have it refilled, or buy a new one. If it is clogged, then run your toolbox utility to clean it.
Mike
Receiving faxes with a Cisco ATA 186
More investigation implies that faxing over VoIP, as I am doing, requires setting the fax BAUD rate to 9600 bps or slower. So does anyone know if it is possible to set the BAUD rate on the Dell MFP 1600n multifunction printers?
Epson Sx200- Paper wont feed
Just a thought,as I had a similar problem.The instructions are abysmal,but it may be worth having a look where you feed the paper in and squeezing the grey plastic gizmo,and moving it to the left to allow the paper to enter the feed properly.
Remove ink cartridge
I found that the proper way to do it only worked when the ink light was flashing red. Then when I pressed the stop button it moved across and stopped beneath the marker to show which cartridge needed changing. The I pressed the stop button again and it moved to a place where I could change it.
This happened despite the fact that the pictures I was printing blatently showed that I needed to replace my ink, it wasn't until I had printed the liney pictures a few times that the printer decided the ink level was low enough to turn the flashing light on and let me change it.
Not finding what you are looking for?