Fisher Ovens - Page 2 - Recent Questions, Troubleshooting & Support
Hello we have a fisher and paykel classic stove
Isolate power from device, remove screws to free back panel.
Loosen strainer for oven liner on left and right sides and remove clip to allow oven liner to slip forward.
Remove screw on front central upper clip.
From front, move oven liner forward a few millimetres to release gasket.
Here you see the strainer at the rear has moved forwards a few millimeters.
Remove the old perished seal.
The new seal/gasket part number 573263 is installed.
Reverse dismantling procedure to complete reassembly.
12/29/2011 12:54:13 AM •
Fisher Ovens
•
Answered
on Dec 29, 2011
Fisher and paykel oven door
you need to either replace - or get the door hinges replaced, the spring in the hinges has weakened over time, if it is still in warranty, then they should replace them for free, if not, then take the model number to your local f&P dealer and buy new hinges. Remove the door and dismantle the door to gain access to the hinges, undo the 2 screws holding each hinge in place, clean the inside of the glas while apart, reassemble in reverse order.
The oven won't turn on. We are unable to set
There are lots of different timers on fisher and paykal
The last one I reset was a few weeks ago it involves pressing 2 buttons at the same time I think it was the oven on and oven off buttons but I am not sure
You will know when you have pressed the right 2 buttons the display will stop flickering set the clock time using the up down arrow buttons
The auto light should not be on if it is press the manual button
Regards
Geoff Stove Recyclers
5/29/2011 5:18:08 AM •
Fisher Ovens
•
Answered
on May 29, 2011
Oven is not coming to
if this is a gas unit then you should check the ignitor by doing an ampere test on the ignitor most ignitors draw 3-3.3 amps minimum when it drops below this amount it takes alot longer for the flame to light if the ignitor checks out good the next thing you would want to check is the oven tempreture sensor this also can be tested by doing an ohms test at room tempreture this should be reading between 1000-1100 ohms if you have any further questions message me back and please remember to rank how this opinion has helped when our chat has concluded thanks Rick
Element for bottom fan forced
You should have 3 wires, the green is the earth. The other two would normally be blue and brown. If you have tried to change the element the missing one may have fallen back in or it could have been burnt off the element terminal and fallen down the back. Anyway you may have to remove the rear of the oven to locate it.
Hi, We have an
The error F4 means that Open oven temperature sensor (RTD)
You need to Check sensor harness and harness connection between oven
sensor and oven control.
Replace oven temperature sensor (RTD) if wiring is
ok.
1/3/2011 11:50:24 PM •
Fisher Ovens
•
Answered
on Jan 03, 2011
Takes long to reach it's
Hello there
Electronic
ovens with a digital display use a sensor to monitor oven temperature.
To solve temperature problems for these models, you may need to replace
the sensor. On some digital-display models, you can calibrate the
temperature using the key pad. See your operator's manual for details.
Ovens
without a digital display often use a mechanical system for controlling
temperature. On many of these units, you can remove the thermostat knob
and adjust the knob itself to more accurately represent the actual
setting of the thermostat.
If,
when you remove the knob, there's a screw on the back of it with a
small calibration plate, you can loosen the screw, adjust the plate,
then tighten the screw again. If the knob isn't adjustable, and the oven
temperature is off by more than 30 to 40 degrees, you need to replace
the thermostat to solve the problem.
I have a fisher and
Hi
Thanks for using FixYa. From what
you have described it seems to be the control panel that has gone bad. You can
leave it unplugged for 5-10 minutes and then check if it flashes with an error
code, if not then it seems to be the control panel that needs to be replaced as the power is getting to the unit however, it wont turn on. Please do
accept the solution if the issue is resolved or post a comment for further
assistance.
Thanks
Rylee
Not finding what you are looking for?