Fisher and Paykel Washing Machines - Page 2 - Recent Questions, Troubleshooting & Support


does fisher paykel have a website ? check with them

Fisher and... | Answered on Jul 07, 2019


hi there the first thing ill tell you is that the washer needs to drain water before it can spin there are only a few factors that prohibit this operation a faulty lid switch secound a blown or blocked water pump being a fisher paykel they are famous for jammed water pumps as they decided when they built the sysyem to turn the water pump upside down this causes a lot of stress on the water pump see if you can lay the hose on the ground and get all the water out i belive the machine will then start to spin dry. in this case it is the water pump and have it replaced its a simple operation if you can order the part fromf/p you simply turn the washer on its side depress the white latch next to the pump turn the pump clockwise till ity release from machine disconnect power supply plug and fit new unit as per reverse


best of luck

sonic boom electronics australia

Fisher and... | Answered on Jul 02, 2019


remove pump check foe anything that may be jamming it,at the same time check the copper windings for any discoloration ,if any replace pump,faulty pumps get hot and after a short time switch off due to a built in thermal cut out

Fisher and... | Answered on Jun 02, 2019


Hi, you should beable to put a thin knife into the slot on the little door flap at the front on the right side and gently pull the door flap down, then unscrew the plug and the water will drain out, put a larg try underneath to catch the water, best to undo the plug enougth so that when the tray is full you can tighten the plug why you empty the tray, all the best.

Fisher and... | Answered on Jun 01, 2019


136. (10001000) Motor Stall
The Motor Control Module has been unable to start the motor. Possible causes of this fault
are: Faulty motor harness, faulty or jammed motor, seized bearings or seals, faulty Motor
Control Module, faulty Rotor Position Sensor or harness.
Primary Source: Wiring.
Action: Measure/check the motor harness, connectors and motor for
discontinuity. This can be done by taking a resistance measurement
between phases of the motor harness at the Motor Control Module
end. Nominal resistance should be around 32Ohms.
Secondary Source: Motor.
Action: 1) Check free rotation of the agitator and basket by rotating by hand.
Bearings and seals may be seized.
2) Check the Rotor Position Sensor and associated harness for
water, mechanical damage or corrosion.
Tertiary Source: Motor Control Module.
Action: If the primary and secondary checks pass inspection, then replace
the Motor Control Module.

Fisher and... | Answered on May 05, 2019


it wont spin if there is water remaining in it,check pump for restrictions or anything jamming it if good replace pump

Fisher and... | Answered on Mar 30, 2019


HI - A 708 EH! A BIT OF AN OLDIE - ANYWAY THE PROBLEM SHOULD BE THE DOOR SWITCH NOT OPERATING.

OK - to repair - unplug the power source - remove 2 screws back top corners, lift the display unit & lay on the lid - on the right side got all the wires going down the machine - locate the first plug has 4 wires , wh - Y- Bl & Bl - BK/BL are thinner and both goes with the rest of the wires & the other 2 you will note goes under the controller - cut & strip the BK/BL so the copper is exposed - use a proper elect connector twist together these exposed wires & join inside the connector.

Assemble & enjoy.

CAUTION - this in effect will overide the lids effectiveness - whilst the machine is operational the opening of the lid will not pause/stop the machine in its tracks like how it should be. Be wary the user safety has been compromised - otherwise try to obtain a replacement if still available for these particular series...

Cheers

Fisher and... | Answered on Mar 04, 2019


blocked or faulty drain pump, remove check for any objects stuck in pump.sniff pump for any burning smell if so replace pump

Fisher and... | Answered on Feb 28, 2019


Does it beep when you switch it on at the wall
Are there any lights showing on the display when you push the power button? or does it seem completely dead

Fisher and... | Answered on Feb 27, 2019


It's best to use a film of petroleum jelly rather than any grease

Fisher and... | Answered on Feb 27, 2019


I can talk you througt this in live chat, but you'd need to get a F&P Bearing replacement toolkit and seals and bearings and a new agitator shaft. cheers

Fisher and... | Answered on Feb 25, 2019

Not finding what you are looking for?
Fisher and Paykel Logo

4,179 questions posted

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...