Fisher and Paykel Washing Machines - Page 8 - Popular Questions, Answers, Tips & Manuals
I have a Fisher Paykel
Fault code 49 is saying that the control board is getting an incorrect reading from the cold water inlet valve circuit. Can be a faulty inlet valve, bad connection on the wiring or more common is that the control board has a fault and will need to be replaced.
9/30/2017 5:45:03 PM •
Fisher and...
•
59 views • 0 helpful votes
Why is lid not locking?
Replace the lid lock. If you post a model number I can give you a part number. Over time lid locks sometimes wear out over time( most of them are 90% plastic). Lid locks should be relatively inexpensive. Also if this is a top load washer you can replace it yourself instead of hiring someone.
8/13/2017 10:18:03 PM •
Fisher and...
•
186 views • 0 helpful votes
Under machine water
Certainly get someone to take a look - neglecting a suspected problem could mean things becoming worse, meanwhile send your daughter into the backyard with a dolly tub, scrubbing board and mangle...
9/17/2017 7:00:03 PM •
Fisher and...
•
64 views • 0 helpful votes
When washing my sheets I get black marks on them.
It sounds like there is a build up of soap powder and it just needs a good clean.Try cleaning the agitator and bowl.
Remove the fabric softener cup from the machine undo the wing nut and take the agitator out and give it a good clean underneath and also while the agitator is out give the bowl a clean down. Then once you have done that and placed the machine back together run the machine through a high water level hot wash with two cups of vinegar added (with no clothing in the machine).
7/22/2017 6:15:03 PM •
Fisher and...
•
281 views • 0 helpful votes
My washing machine was on
Could be a overheating pump. hope you got it checked out! probably blew the board when the pump went.
8/30/2017 7:33:02 AM •
Fisher and...
•
96 views • 0 helpful votes
How to install fuse gwl11
You need to be more detailed in the description. What is the fault code & is it the same code as before the pump was changed? Why did you change the pump? Was the old pump tested & proven to be faulty or did you just change it in the hope that it would fix the fault? I have changed many F&P smartdrive pumps & never seen or heard of any having a fuse. The only fuse is on the main control board, soldered in. If that had blown the machine would not power up, so fuse must be okay. Start from scratch & say what the error code is.
6/8/2017 8:57:02 PM •
Fisher and...
•
805 views • 0 helpful votes
Smart drive 085
It won't spin until all the water is drained out. The drain pump may be blocked or faulty. Fix the drain pump fault first then deal with the filling issue. They will not be related.
6/21/2017 9:30:03 AM •
Fisher and...
•
291 views • 0 helpful votes
We have a fisher and
If it is a musical rippling sound & hot & cold lights are flashing that usually indicates it is not getting water quickly enough. You can open the lid while it is filling & look. If water is just trickling in and taps are fully open then replace the inlet valve with a new one.
6/26/2017 8:33:03 PM •
Fisher and...
•
179 views • 0 helpful votes
Hello,
I live in Dubai and
First question that comes to mind is why you would want to have a machine if their is no service support where you live. I assume you have done the basics like taking hose off machine inlet and pointing it in to a tub, turn tap on and make sure there is a good supply of water. Put hose back on machine, fully open tap & start (on cold supply). Lift lid while it is filling. Check that a strong flow is coming in to machine. Then repeat with the hot tap. If water is only trickling in & sounds like it is struggling then more than likely it needs a new inlet water valve.
7/15/2017 3:42:03 AM •
Fisher and...
•
105 views • 0 helpful votes
Wa75t65gw1
After 2 minutes does the machine throw up an error code. Starts beeping and shows a weird pattern of lights?
If so that error code can help us diagnose what your problem is.
If it does give you an error code take a photo and post it back on here so I can see what it is.
7/4/2017 10:00:03 PM •
Fisher and...
•
125 views • 0 helpful votes
Washer gets to rinse cycle and starts to pump water then stops?
Before hitting any buttons you need to write down the fault code. As soon as it starts beeping take note of which lights are on along the top row. There are 8 lights. Count from the right and tell us which number light is on and which are off. That will tell us the error code and what it means.
5/30/2017 1:42:03 PM •
Fisher and...
•
217 views • 0 helpful votes
Not finding what you are looking for?