Fisher and Paykel Washing Machines - Answered Questions & Fixed Issues


What appliance is it?

Fisher and... | Answered on Nov 14, 2019 | 30 views


ask google . it is not my brand sorry

Fisher and... | Answered on Nov 11, 2019 | 36 views


If you cannot see the water leaking from the inlet valves, check the seal just above the water pump located directly under the drum. I am in the midst of awaiting parts to fix this very thing on my FP GWL11. This leak is dripping water directly onto the motor, causing it to trip the circuit breaker during drain/spin cycles.

Note... I have also had to have the inlet valve assembly replaced as well as it was not opening to allow cold water to mix with the hot.

Hope this helps.

Fisher and... | Answered on Oct 01, 2019 | 2,284 views


that is a sizing problem ,if neither board has been replaced recently,then faulty board

Fisher and... | Answered on Sep 28, 2019 | 56 views


if its a top loader then a faulty motor controller.(computer main board )

Fisher and... | Answered on Sep 28, 2019 | 65 views


That means that power is being applied to the drain pump when it shouldn't be. There is only one reason for that, a fault in the main control board. You will have to replace the main board.

Fisher and... | Answered on Sep 17, 2019 | 39 views


would need more info

Fisher and... | Answered on Sep 08, 2019 | 575 views


each element switch controls the heat to that element so those switches need to be replaced ,technical name is simmerstat

Fisher and... | Answered on Sep 08, 2019 | 46 views


It beeps to tell you there is an error. While it is beeping & before pressing any buttons, read the error code & write it down. The error code is the lights along the top row. Count from left to right and make a note of exactly which lights are on and which are off. There are 8 lights, you need to say exactly which number light is on. Post the result back here and someone will tell you what that error code means.

Fisher and... | Answered on Jul 11, 2019 | 83 views


Make sure that the washer drain hose is at least 30 inches above where it comes out of the washer or 38 from the ground. the washers drain hose needs to be typically higher than the washer. Could also be a faulty pressure switch depending on the washer See video link.

.https://products.geappliances.com/appliance/gea-support-search-content?contentId=17418

Fisher and... | Answered on Jul 10, 2019 | 31 views


hi there the first thing ill tell you is that the washer needs to drain water before it can spin there are only a few factors that prohibit this operation a faulty lid switch secound a blown or blocked water pump being a fisher paykel they are famous for jammed water pumps as they decided when they built the sysyem to turn the water pump upside down this causes a lot of stress on the water pump see if you can lay the hose on the ground and get all the water out i belive the machine will then start to spin dry. in this case it is the water pump and have it replaced its a simple operation if you can order the part fromf/p you simply turn the washer on its side depress the white latch next to the pump turn the pump clockwise till ity release from machine disconnect power supply plug and fit new unit as per reverse


best of luck

sonic boom electronics australia

Fisher and... | Answered on Jul 02, 2019 | 2,610 views


remove pump check foe anything that may be jamming it,at the same time check the copper windings for any discoloration ,if any replace pump,faulty pumps get hot and after a short time switch off due to a built in thermal cut out

Fisher and... | Answered on Jun 02, 2019 | 54 views


Hi, you should beable to put a thin knife into the slot on the little door flap at the front on the right side and gently pull the door flap down, then unscrew the plug and the water will drain out, put a larg try underneath to catch the water, best to undo the plug enougth so that when the tray is full you can tighten the plug why you empty the tray, all the best.

Fisher and... | Answered on Jun 01, 2019 | 416 views


136. (10001000) Motor Stall
The Motor Control Module has been unable to start the motor. Possible causes of this fault
are: Faulty motor harness, faulty or jammed motor, seized bearings or seals, faulty Motor
Control Module, faulty Rotor Position Sensor or harness.
Primary Source: Wiring.
Action: Measure/check the motor harness, connectors and motor for
discontinuity. This can be done by taking a resistance measurement
between phases of the motor harness at the Motor Control Module
end. Nominal resistance should be around 32Ohms.
Secondary Source: Motor.
Action: 1) Check free rotation of the agitator and basket by rotating by hand.
Bearings and seals may be seized.
2) Check the Rotor Position Sensor and associated harness for
water, mechanical damage or corrosion.
Tertiary Source: Motor Control Module.
Action: If the primary and secondary checks pass inspection, then replace
the Motor Control Module.

Fisher and... | Answered on May 05, 2019 | 1,343 views


You may need new brushes in the motor

Fisher and... | Answered on Apr 19, 2019 | 78 views


it wont spin if there is water remaining in it,check pump for restrictions or anything jamming it if good replace pump

Fisher and... | Answered on Mar 30, 2019 | 1,347 views


blocked or faulty drain pump, remove check for any objects stuck in pump.sniff pump for any burning smell if so replace pump

Fisher and... | Answered on Feb 28, 2019 | 38 views


Does it beep when you switch it on at the wall
Are there any lights showing on the display when you push the power button? or does it seem completely dead

Fisher and... | Answered on Feb 27, 2019 | 51 views

Not finding what you are looking for?
Fisher and Paykel Logo

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...