Frigidaire Logo

Frigidaire Recent Questions, Troubleshooting Help & Support

  • 3K Products
  • 135K Answers
  • 3M Views

The pipe on the defrost drain has come off. Pul the fridge out and look for a pipe that goes to a tray on top of the compressor.

Also look for the drain channel in the back of the fridge. Something may have blocked the hole.

Or call the dealer under warranty.

https://www.frigidaire.com/Owner-Center/Product-Support--Manuals/?productCode=FFPS4533QM

Frigidaire... | Answered on Jan 21, 2020


Be aware the fridge works with deadly voltages. If you have not enough technical knowledge, please don't do this yourself.
With a multi meter you can measure if the voltage you apply is entering the fridge. There is not much in a fridge. You find a on / of switch, a thermostat en mostly an override switch too short a thermostat. So if you measure a voltage coming is, follow the wiring and check what the thermostat does. if it won't switch you have the cause. If it does switch, follow the wiring, and if the aggregate gets a voltage and does not run, you have a defective aggregate. I can't think of more.
Good Luck.

Frigidaire... | Answered on Jan 14, 2020


Hi,

The F10 F11 F12 F13 F14 Error Codes indicate that the electronic oven control board senses a runaway temperature condition in the oven through the oven sensor circuit.
This can be caused by a faulty oven temperature sensor probe or a failed electronic control board.
Oven temperature is detected by the control board as it monitors the resistance through the oven temperature sensor circuit.
You could have a failed oven temperature sensor, a wiring harness failure, an open thermal switch or a failed electronic oven control board that would cause this problem.
The first component to check would normally be the oven temperature sensor probe.
If you have a volt/ohm meter, you can shut off the breaker for the range and remove the screws that mount this sensor to the back wall of the oven.
Carefully pull the wire harness into the oven cavity until you get to the wire harness disconnect plug.
You should have enough slack to pull it this far into the oven.
Disconnect the sensor but do not let the wire harness retract back through the back wall of the oven or it will be hard to reconnect.
Measure the resistance of the oven temperature sensor with your volt/ohm meter. At room temperature, the resistance should measure around 1100 ohms.
The resistance chart is shown in the image below.

If the resistance is above 2200 ohms at room temperature, then the sensor probe is causing the F10 error code and will need to be replaced.

You can order a new sensor probe from the Sears PartsDirect website. The part number for the sensor is 316217002.

If the resistance is normal, then one of the other causes mentioned above is producing your F10 code.
You would need to access the electronic oven control board (Timer) in the console and check the resistance at the sensor circuit connection to the control board as the next step in troubleshooting this problem.


http://media.fotki.com/1_p,wbqdsfkrfqtswfqxgtqsskgwtqkq,vi/krdbrtqkgxkrbbqbrwb/1/1303472/5961857/image37801img-or.jpg


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Thanks to blueextc3221 for this solution.

Frigidaire... | Answered on Jan 09, 2020


Good Afternoon Friend,

I understand that your Frigidaire refrigerator, model# FFHS2611LWF, is flashing an "H1" code. This is actually stating "HI", as in either the refrigerator or freezer, temperatures are Hi and not at a safe level. First, press any button to stop the alarm and clear the HI temperature. If you are still receiving the alarm, I suggest checking the freezer, to make sure that everything is still frozen, and nothing is defrosting as, well as checking the refrigerator temperatures. If things are defrosting or the temperature is Hi in your refrigerator, I suggest resetting your appliance, by either unplugging it or shutting the power off at your homes circuit breaker, for 3-5 minutes. When power is restored, Give your freezer 24 hours to stabilize at the default temperatures of 0 degrees for the freezer and 37 degrees for the refrigerator. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your refrigerator status has changed successfully.

-Best Regards-
WP

Frigidaire... | Answered on Jan 07, 2020


the drain pipe could be having a block. some times buttons and coins are the culprits.

Frigidaire... | Answered on Jan 06, 2020


The F10 error can be caused by a faulty relay or electronic control board if the oven overheated while in use. If you unplug the range and the error occurs when the range is cool, then the over-temperature sensor has failed or the electronic control board is faulty. Even the wiring between parts could be faulty.

You need to check sensor and wiring. On some models, the oven temperature sensor probe can be accessed by opening the oven door. Look for two screws that are close together. Otherwise it's accessed from the back of the oven. It may be covered by an access panel. Unplug the wiring harness and check the resistance across the sensor with a multi-meter. It should give 1100 Ohms. Similarly check the wiring resistance from the probe to the control board. Also check the relay and that wiring. Replace the wiring, sensor or relay if those are faulty. Otherwise you need to replace the control board. The control board will be behind the console access panel. Somewhere on the back of the range, there will be a trouble-shooting sheet giving the wiring diagram and the expected resistance or voltage across the parts of the range.

I may be able be able to provide a parts diagram and price list for parts on your range. Please add a comment with the model number of the range for this information.

I hope this helps.

Cindy Wells

Frigidaire Ovens | Answered on Jan 04, 2020

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Frigidaire Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Brad Brown

Level 3 Expert

18157 Answers

Cindy Wells

Level 3 Expert

6069 Answers

Are you a Frigidaire Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...