Frigidaire Washing Machines - Page 4 - Recent Questions, Troubleshooting & Support

door switch faulty

Check and clean/clear bottom drain screen if have one pump operating properly and main drain line for clogging

sounds like the transmission needs replaced

assuming this has long since been dealt with, but if its not in the rubber gasket at the front of the machine, take off the bottom panel at the front, there is a small pump there that drains the unit. It may be trapped in there. You can use pliers or vice grips to remove the couplers holding the hoses on and a screwdriver to remove it.

Replace the failed bearing at the rear.

Try pressing and holding the Delay Start button for ~3 seconds. The 'loc' indicator should go out. If you hold the button for too long, then the lock could toggle back on. If the problem persists, you may have an issue with the keypad on the dishwasher. I hope this helps. Please add a comment with the model number of the dishwasher if the control panel lock does not disengage. Cindy Wells

i had to hold the options and select buttons down at the same time about 3 seconds and bingo it works again

either belt loose or agitator cogs under agitator bad

Good Afternoon Friend, I understand that your Frigidaire Affinity washer, model# ATF705BZHS, is not filling with water and showing an E11 error code. The E11 code means that your washer is taking a long time to fill. First, make sure that the incoming water faucets are turned on. Next, you will want to make sure that the pressure is above 30 PSI. I suggest resetting your washer, by either unplugging it or shutting the power off at your home's circuit breaker for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. Hope this is helpful. -Best Regards- WP

No model number stated. R134a is the type of refrigerant used!

possible stuck clutch in transmission

possible bad start up capacitor to motor

The Frigidaire Affinity Washer Error E41 is a door lock error. It means the primary control thinks the door is open. If the door is closed and this error persists, then in most cases, you will need to replace the door lock assembly on the washer. Sometimes this error can be caused by the control board, but it's more common for the door lock assembly to have failed than the control board.

solenoid valve is probably faulty, it is usualy located at the top of the machine close to the drawer

Hello 2cats - First, is the drain pump making a humming noise? If so, the unit could possibly have a restriction in the drain line. Try setting the cycle to spin only and verify if water pumps out. Other possibilities could be a faulty door lock, timer, pump, or control board not communicating correctly. In this case I would contact a professional to move forward accurately to properly diagnose and repair the washer.

Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101

Just follow these steps:

1. Remove the center dispenser from the top of the agitator. It should just pop off.
2. Locate the white plastic cap underneath and pull straight up to remove.
3. Locate the agitator bolt underneath and remove using a socket and ratchet (can't remember the size). Hold the agitator still with one hand in order to loosen the bolt.
4. With the bolt removed, grasp the agitator by the bottom flanges and pull straight up. It should lift off the center post.

NOTE: Sometimes these agitators will stick due to years of detergent accumulation. You may have to wobble it back and forth to get it loose.

If you have questions, please let me know. I hope this helps you.

If it beeps during the fill cycle it is possible that there is not enough water going into the machine. Turn the water off and where the hose goes into the machine, there is a bowl shaped gauze screen and a sealing washer. The gauze may be blocked with debris or limescale. Clean with a brush and soak in vinegar or CLR. Also test the tap to the hose by having someone hold the hose in a bucket, whilst you turn the water on. https://www.amazon.ca/LiXiongBao-Stainless-Coupling-Strainer-Connector/dp/B086J4L47D/ref=asc_df_B086J4L47D/?tag=googleshopc0c-20&linkCode=df0&hvadid=459590544144&hvpos=&hvnetw=g&hvrand=2862470894891564456&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9000809&hvtargid=pla-945096412703&psc=1 ..

If you house water pressure seems normal check the following pressure switch, lid switch and the water inlet valve. Also check for any blockages in the water lines check the water screen where the water lines hook into the wash clean screen with toothbrush and soap .

A LOCAL REPAIR SERVICE