Frigidaire Washing Machines - Page 3 - Popular Questions, Answers, Tips & Manuals

Common solutions for: Frigidaire Washer won't spin or agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. If the lid switch assembly fails, the washer will not spin.

SOUNDS LIKE A BAD TIMER

either belt loose or agitator cogs under agitator bad

Replace the failed bearing at the rear.

The Frigidaire Affinity Washer Error E41 is a door lock error. It means the primary control thinks the door is open. If the door is closed and this error persists, then in most cases, you will need to replace the door lock assembly on the washer. Sometimes this error can be caused by the control board, but it's more common for the door lock assembly to have failed than the control board.

If it beeps during the fill cycle it is possible that there is not enough water going into the machine. Turn the water off and where the hose goes into the machine, there is a bowl shaped gauze screen and a sealing washer. The gauze may be blocked with debris or limescale. Clean with a brush and soak in vinegar or CLR. Also test the tap to the hose by having someone hold the hose in a bucket, whilst you turn the water on. https://www.amazon.ca/LiXiongBao-Stainless-Coupling-Strainer-Connector/dp/B086J4L47D/ref=asc_df_B086J4L47D/?tag=googleshopc0c-20&linkCode=df0&hvadid=459590544144&hvpos=&hvnetw=g&hvrand=2862470894891564456&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9000809&hvtargid=pla-945096412703&psc=1 ..

No model number stated. R134a is the type of refrigerant used!

possible bad start up capacitor to motor

Check and clean/clear bottom drain screen if have one pump operating properly and main drain line for clogging

possible stuck clutch in transmission

Frigidaire Washer/Dryer Combo: Model GCET1031FS2 Parts ...

www.repairclinic.com > ProductDetail

Frigidaire Washer/Dryer Combo Model GCET1031FS2 Parts. Frigidaire ... If the dryer overheats, the thermal fuse blows to cut off power to the dryer. If the thermal ... ..

Possibly water level sensor failed

If you house water pressure seems normal check the following pressure switch, lid switch and the water inlet valve. Also check for any blockages in the water lines check the water screen where the water lines hook into the wash clean screen with toothbrush and soap .

PROBABLY A BAD CONTROL BOARD

A LOCAL REPAIR SERVICE

HOLD THE LOCK BUTTON FOR 10 SECONDS

As ­e­l­iz­A­b­et­h r­e­p­l­i­e­d ­i'­m ­A­m­Az­e­d t­h­At ­A ­m­o­m ­c­A­n ­e­Ar­n $7438 ­i­n ­f­our w­e­e­ks ­o­n t­h­e ­c­o­m­put­er. ­d­i­d y­ou s­e­e t­h­is s­it­e ­g­o t­o t­h­is s­it­e ­h­o­m­e t­A­b ­f­or ­m­or­e ­d­et­A­i­l.......www.job.pays12.com

Could be cycle timer failure

Recheck the outlets and if they are on the same circuit as the dryer then you could have a problem with the wiring . My feeling if the living room outlets were changed there should be no connection between the living room and utility room. One way of telling is to get an extension cord and hook it to your dryer and to different outlets in the house that you know is working.f there is power on the living room receptacles then plug the dryer extension into them.

the drain pipe could be having a block. some times buttons and coins are the culprits.