Frigidaire Washing Machines - Page 6 - Answered Questions & Fixed Issues
What is the capacity of Frigidaire washer GLTF1240A
The Frigidaire GLTF1240A clothes washer has a tub capacity of 2.65 cubic feet. Under typical conditions, based on a yearly average of 392 loads of laundry, the Frigidaire GLTF1240A is estimated to use 341 kilowatts of energy per year. Obviously, this number will vary depending on things like the size of loads that you wash, and temperature at which you wash your clothes. Also, this figure is calculated according to a test done by the US Department of Energy which takes into account the energy consumed by the washer as well as the energy needed to heat the water with an electric water heater. If you use a gas water heater you will probably use fewer kilowatt hours but you will consume gas to heat the water.
Its estimated water use is 9,806 of gallons per year. It is estimated to use 9.4 gallons per cycle, per cubic foot of tub volume. You can use this "per cycle, per cubic foot" to compare washers against each other. The lower the number, the more efficiently the washing machine uses water, assuming your clothes are equally clean after being washed in either washing machine.
5/8/2019 11:31:25 AM •
Frigidaire...
•
Answered
on May 08, 2019
•
564 views
Why does clothes get stuck under my Frigidaire stackable washer
http://www.fixya.com/tags/clothes_stuck_agitator_washing_machine/browse/frigidaire
To prevent clothing from knotting and twisting:
- Avoid mixing heavy items with light items.
- Avoid putting too many or too few items in the washer.
- Make sure you set the proper water level for the size load you are doing. ...
- Never wrap the clothes around the agitator. ...
- Be sure your wash water is not too hot for the fabric
3/6/2019 6:07:07 PM •
Frigidaire...
•
Answered
on Mar 06, 2019
•
2,220 views
The door on my fridgidaire atf8000fs1 sags so it
Frigidaire washer door sagging so strike and door lock not lining up correctly. After a period of time front load washer doors tend to start to drop below normal position. The glass in the front doors are very thick, heavy and only supported by plastic inner frame. This combined with continued opening and closing will over time make your front load door start to sage. Fortunately Frigidaire makes a door shim kit for this problem.
After you have ordered and received the shim kit part #137309800. Start with removing the three screws holding the door to the machine. Lay the door face down on a soft surface as to no scratch the front of the door and glass. Remove the screws securing the outer frame and with a very small flat screw driver shim it between the inner and outer panels. Make sure to note the position of the frame and glass. Next remove the inner plastic frame, you should have access to the hinge at this point. Install the shim kit according to the instructions that come with the kit. Reinstall the hinge, inner frame and screws. Install the door back onto the washer, your door strike and lock should line up in the correct position at this time.
i got this answer at
http://www.appliancerepairquestion.com/2013/04/frigidaire-atf8000fs1-washer-door-not.html
2/7/2019 7:43:45 AM •
Frigidaire...
•
Answered
on Feb 07, 2019
•
2,632 views
What how to do diagnostics on a frididaire front loader atf6000es
Have you checked the drive belt and the motor brushes? Also check if there is voltage getting to the motor. Does then drum fill with water, and carry out the wash cycle fully but without the drum moving? If so it is likely to be either the motor, brushes, belt or relay pcb
1/19/2019 10:57:38 AM •
Frigidaire...
•
Answered
on Jan 19, 2019
•
106 views
Not finding what you are looking for?