GE Washing Machines - Page 7 - Recent Questions, Troubleshooting & Support


Some have a nut that holds agitator in place. If it does, it would be under top removable agitator cap. If there is no nut, agitator snaps off by slipping fingers under agitator at 3 and 9 o’clock positions and pulling up hard and fast.

GE Washing... | Answered on Dec 12, 2018


Hi,
The soleniod valve is bad.... here is a tip that will help...

http://www.fixya.com/support/r3880845-washing_machine_problems_no_water

heatman101

GE WDSR2080D Top... | Answered on Dec 10, 2018


Tub bearing and seal is either worn or improperly installed.

GE Washing... | Answered on Dec 10, 2018


The H20 error is a low-water flow error. It could be a problem at the inlet (shut-off closed, low flow through the hoses), the inlet valves, the pressure sensor/air tube that checks how much water arrived in the tub in about 8 minutes or a problem with the controller getting the correct messages.

Since some water arrived in the washer, close the shut-off valves and take the hoses off. Check for debris in the filters (in the hoses and the inlet valves on the washer). Put a bucket under the hoses and check the water flow from each hose. If you have low water flow, replace the hoses and check for any other places that could be clogged or leak. Make sure that the drain hose outlet isn't below the normal fill level in the washer.

Check the pressure system and reed switch that determine the amount of water in the tub. If the air tube is clogged, remove the blockage. Check that the inlet valves are opening and closing properly. Finally, check that the control board and wiring to make sure that the water level signals are reaching the control board. For some GE washers, there is a reset for the control board that is described on the diagnostic sheet inside the washer near the control panel. Try to reset the error message following the directions.

I hope this helps. Please add a comment with the model of the washer for further instructions on testing for and finding the problem.

Cindy Wells

GE Washing... | Answered on Dec 08, 2018


Did you replace main control board or motor control board?

GE Washing... | Answered on Dec 07, 2018


Your washer can develop several types of leaks. You can track down a leak based on when it occurs:

During fill only
During drain and spin only
All the time
During fill only If the washer leaks only during the fill cycle, check these:

  • Air-gap device -The air gap is a small device found on most washers that prevents the wash water from being siphoned into the household water supply. It's located either mid-way along or at the end of the black rubber hose that comes from the water-inlet valve. Often it's made of translucent plastic. If one of the air-gap components deforms or cracks, you may need to replace it.

  • The tube -There's a rubber tube that runs between the water-inlet valve and either the air-gap or the inlet spout. If it cracks or breaks, it can cause a leak.

  • Inlet spout -Most washers have a plastic spout near the top of the main clothes tub that directs the water into the tub. If the spout cracks or breaks free of its mounting, it can cause a leak.

During drain and spin only A washer that leaks only during the spin cycle often has a leak in the main drain hose. Inspect the entire hose and correct any problem you find. Alternatively, the steel or plastic outer tubs can rust, split, or be punctured. This may be most visible during large loads and high water levels. If this happens, you may have to replace the entire outer tub--but that may not be an economical repair to make. Consult a qualified appliance repair technician for further details.

All the time If the washer leaks all the time, check these:

  • Hot and cold water fill hoses - Check the hot and cold water hoses from the household plumbing. If either hose is leaking, tighten it or replace it, as appropriate.

  • Main tub seal - The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft entry point. If this seal leaks, you can see the leak by opening up the machine's main access panel while the machine is full of water with a small amount of detergent in it. The leak appears at the underside of the outer tub, at or near the center. This seal is difficult to replace. You probably should call a qualified appliance repair technician.

  • Pump - If the pump leaks, you can probably spot the leak when the tub is full of water. The pump has two or more black rubber or plastic hoses attached to it and usually has a drive belt that spins the pump. If the pump is leaking, you need to replace it.

  • Outer tub - Over time, the steel or plastic outer tubs can rust, split, or be punctured. If this happens, you may have to replace the entire outer tub--but that may not be an economical repair to make. Consult a qualified appliance repair technician for further details.

GE WJSR2070B Top... | Answered on Nov 30, 2018


Try buttons "dry" & "spin" together for a few seconds. This is the child lock display.

Or press "end of cycle" for over 5 seconds.

Or press "options & select" till the light goes off.

Works for other machines..............And please rate me if helped

GE WSXH208A... | Answered on Nov 24, 2018


Check on line normally the manufacturer will have the book or pictures on there site

GE Washing... | Answered on Nov 10, 2018


Parts #: WH12X25294 location #632 located at motor plug in area

WH12X26330 - GE Washer Speed Sensor from Parts Dr.
GE
Washer Speed Sensor. This is a new GENUINE GE replacement part.
See more details at Parts Dr. »
+$7.49 shipping. No tax
Parts Dr.
96% positive (5,377)

GE Washing... | Answered on Nov 08, 2018


Check hose and valve screens for debris

GE Washing... | Answered on Nov 04, 2018


No it work with th electronics so the machine will operate and reset for each load

GE Washing... | Answered on Nov 03, 2018


Could be agitator itself making noises, could be transmission noise, maybe timer movement you’re hearing. Hard to say. Probably need someone reputable to check it.

GE Washing... | Answered on Nov 01, 2018

Not finding what you are looking for?
GE Logo

9,366 questions posted

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

geapptech

Level 2 Expert

157 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...