Haier Dryers - Recent Questions, Troubleshooting & Support
Haier gas dryer rdg350aw won't heat up
Let's troubleshoot this issue and find a compatible heating element.
Check the Igniter: The igniter is responsible for lighting the gas burner. If it's faulty, the dryer won't heat. Inspect the igniter for any visible cracks or damage. If needed, replace it.
Thermal Fuse: The thermal fuse is a safety device that cuts off power to the heating element if the dryer overheats. Check if the thermal fuse is blown (no continuity). If so, replace it.
Gas Valve Solenoids: These solenoids control the gas flow to the burner. If they're defective, the dryer won't heat. Test them for continuity using a multimeter. Replace if necessary.
Heating Element: Since you specifically asked about the heating element, let's focus on that. The compatible heating element for your Haier gas dryer model RDG350AW is the Haier Dryer Heating Element (Genuine OEM Part # WE11X27362). You can find it online or at appliance parts stores.
3/7/2024 7:07:58 AM •
Haier Dryers
•
Answered
on Mar 07, 2024
DRYER STOPPED VENTING
sounds like the lint is blocking the exhaust to outside vent, remove the vent and pipes from dryer and clean.
The second thing that may be a problem is the "thermister" , this is a temperature sensing device that may need replacing, the purpose for this is to prevent fires from overheating.
Where is the thermal fuse on Haier Dryer model HLTD600AEW?
The location of the thermal fuse on a Haier Dryer model HLTD600AEW may vary depending on the specific model and design of the dryer. However, in general, the thermal fuse is usually located near the heating element or the exhaust duct. It may be hidden behind a panel or tucked away in a hard-to-reach area. In some cases, it may be necessary to consult the user manual or contact the manufacturer for specific instructions on how to locate the thermal fuse on a Haier Dryer model HLTD600AEW.
1/20/2023 5:53:31 PM •
Haier Dryers
•
Answered
on Jan 20, 2023
Haier dryer rde 350 aw will not start beep and a click is all i get
Based on the description provided, it sounds like there could be an issue with the start button or the control board on your Haier RDE 350 AW dryer.
- Check that the start button is not stuck or malfunctioning. If the button is stuck, it may not be able to send the proper signal to the control board to start the dryer.
- If the start button is working properly, the issue may be with the control board. The control board is responsible for sending power to the various components of the dryer, including the motor. If the control board is malfunctioning, it may not be able to send the necessary power to the motor, resulting in the clicking noise you're hearing.
If the above solutions don't resolve the issue, it's best to contact Haier customer service for further assistance. They can provide troubleshooting steps or arrange for a technician to come out and look at the dryer. Request for a senior technician or supervisor to take a look at it and provide a resolution.
1/18/2023 12:00:46 AM •
Haier Dryers
•
Answered
on Jan 18, 2023
Haier encore dryer beeps and lights up but doesnt turn on
There could be a few potential causes for this issue with your Haier Encore dryer.
- The first thing to check is whether the dryer is properly plugged in and the circuit breaker has not tripped.
- If the dryer is properly plugged in and the circuit breaker is fine, there may be an issue with the door switch. The door switch is a safety feature that prevents the dryer from turning on if the door is open. Make sure the door is closed securely and check that the switch is not stuck in the open position.
- Another potential issue could be with the control board, which is responsible for controlling the functions of the dryer. If the control board is malfunctioning, it may prevent the dryer from turning on even if all other components are working properly.
If none of these solutions resolve the problem, it is best to contact Haier customer service for further assistance. The dryer is less than 8 months old and should be covered under warranty. It's also possible that the problem is caused by a faulty part that needs to be replaced. Request for a senior technician or supervisor to take a look at it and provide a resolution.
Regenerate response
How to out the drum back on
I'm experiencing the same issue. I took apart the dryer to find no possible way to correct the sagging/drooping gap. help!
NEED TO REPLACE THE FAN BELT ON HAIER DRYER MODELHLP140E
Remove the lint trap. There is a bolt in the center. Remove bolt. Remove screws from crossbar and you can then replace the belt. I removed sensor and lifted drum out makes it easier. Pay attention to how black belt is thread if removed
Where is the thermal fuse located on a Haier RDE350AW dryer ?
Not exactly a fuse for drying heat, the electric motor would have a thermal fuse strapped into the winding.
The dryer exhaust hot air chimney, just after the drum, would have both a thermostat and a high heat limit called thermodisk cut off and clixon by trade name.
Find the wiring diagram inside the dryer panels to reveal color wires going to what you need finding.
8/19/2019 1:16:39 AM •
Haier Dryers
•
Answered
on Aug 19, 2019
I don't know how to
I own the Haier Dryer and found the red/orange fan belt by searching part # WD-0350-37 @APPLIANCE PARTS DEP(-APPLIANCE PARTS DE DALLAS TXUS. The part was cheaper than the other places and the shipping was actually slightly lower. Now putting the belt on was a bit tough. I finally figured out that I needed to remove the bolt inside the dryer with a ratchet.
How do you turn off the beaping on a Haier Clothes Dryer?
The responses here miss the issue: The beeps described by the Poster are NORMAL and signal a finished load. However, the beeps are very loud, persistent, and extremely annoying, therefore the Poster wants to DISABLE the beeps. The question is how to disable the annoying beeps.
12/11/2018 12:23:35 AM •
Haier Dryers
•
Answered
on Dec 11, 2018
How to reset my haier dryer
Pull the plug. Reconnect after 30 seconds. If there is a fault you need to fix the fault first as the fault will continue to stop the dryer. Faults may be solved by reading the troubleshooting section in the user manual.
Not finding what you are looking for?