Hamilton Beach Coffee Makers & Espresso Machines - Recent Questions, Troubleshooting & Support

I was able to fix this:1. Remove top cover2. Remove grate, one screw3. Dump water4. Clean water sensor probe (silver colour, bullet shape, approx 1/4" long), use a small flat screw driver with paper towel to remove any build up.5. Plug in and test until it works.if you get it to work again, that would be a good time to run the vinegar solution through.

Question edited for clarity. Question moved from Washing Machines category. Help in the link https://www.google.com/search?q=Hamilton+Beach+HSDCU60C+coffee+maker.+E3+error ..

These machines needs regular dealer service, but of course they don't tell you that when you buy them. Contact their support and request warranty assistance. Some ideas here https://www.google.com/search?q=hamilton+beach+coffee+maker+says+add+water

FlexBrew® Coffee Makers

Hamilton Beach https://hamiltonbeach.ca > flexbrew-coffee-makers With a FlexBrew® coffee maker in your kitchen, you'll enjoy maximum brewing flexibility. You can brew into a cup or travel mug, enjoy up to 10 oz. of coffee ...

FlexBrew® Trio Coffee Maker (49902C)

Hamilton Beach https://hamiltonbeach.ca > flexbrew®-trio-coffee-mak... Enjoy the versatility of 3 ways to brew with the Hamilton Beach® FlexBrew® Trio Coffee Maker. Brew a single cup in about 90 seconds with a single serve pod ... $159.99 · ‎ In stock ..

What does the eo6 code mean on Hamilton Beach brew station

The replacement lid can be found at:

http://www.forumappliances.com/i-656-Hamilton_Beach__cover_lid_.html

48.8889 C is equal to 120 F

Question edited for clarity. How about a new grinding cup for $10? https://hamiltonbeach.com/removable-grinding-chamber-990099602 There seems little support and no parts diagrams that show how the parts fit together. There are a couple of videos that may help as all models work to a theme where the grinding cup is concerned. Manual and Hamilton Beach contact details https://www.manuals.ca/hamilton-beach/80393/manual ..

If the power light is flashing on your Hamilton Beach Single Serve Coffeemaker, there could be a few different issues that may be causing this. Here are a few things you can try:

1. Check the water reservoir: Make sure that the water reservoir is properly inserted and filled with water. If the water level is too low or the reservoir is not inserted correctly, the coffeemaker will not turn on.
2. Check the coffee pod holder: Make sure that the coffee pod holder is properly inserted and that the lid is closed securely. If the coffee pod holder is not inserted correctly, the coffeemaker will not turn on.
3. Check the power cord: Make sure that the power cord is plugged in securely to both the coffeemaker and the electrical outlet.
4. Unplug the coffeemaker: If none of the above solutions work, try unplugging the coffeemaker from the electrical outlet and wait for a few minutes before plugging it back in. This can sometimes reset the machine and fix any issues.

If none of these solutions work, it may be a more serious issue with the machine and you may need to contact Hamilton Beach customer service for further assistance.

There are a few possible reasons why the coffee dispenser bar on your Hamilton Beach

1. Check the water level in the reservoir. Make sure that there is enough water in the reservoir to brew a full pot of coffee. If the water level is too low, the coffee dispenser bar may not work properly.
2. Clean the coffee dispenser bar. Over time, coffee grounds and other debris can accumulate on the coffee dispenser bar, clogging it and preventing the coffee from flowing properly. To clean the bar, run a solution of equal parts water and vinegar through the coffeepot and then rinse it thoroughly.
3. Check the filter basket. Make sure that the filter basket is properly seated in the coffeepot and that it is not clogged with grounds. If the basket is not properly seated or is clogged, it may prevent the coffee from flowing through the dispenser bar.
4. Check the gasket. The gasket is a rubber seal that helps to create a tight seal between the carafe and the coffeepot. If the gasket is damaged or worn, it may cause a leak and prevent the coffee from flowing through the dispenser bar.

If none of these troubleshooting steps resolve the issue, it is possible that there is a problem with the coffeepot itself. In this case, you may need to have it repaired or replaced.

Push "Carafe" button.

There is a spring between the lever and the o-ring. It may have popped out when you cleaned the pot. That has happened to me before. The spring is necessary to hold the seal down until the lever is pushed.

Try tapping the other way. You may have unseated the motor's carbon brushes. or Send it back under warranty. https://hamiltonbeach.ca/customer-service ..

Mine does the same. Very annoying and the unit is 3 months old. I cleaned the unit yesterday and no help. I'll call HB today and see if they can help.

Found the answer in an Amazon review. Place a small bamboo stick in the water sensor located in the resevoir. The ERR code disappears and you can brew as normal. If you leave the stick in, measure water carefully as there is no auto shutoff.

you need to replace it when it doesn't make coffee anymore

Normally there are no lights which does signify off. To check, disconnect from the mains electricity supply for 5 minutes and plug back in. https://www.google.com/search?q=hamilton+beach+flexbrew+coffee+maker+manual ..

Unplug the unit for 30 minutes or longer - it should reset the coffeemaker and the clean light.

Report this potentially dangerous defect to Hamilton Beach.

On my old Hamilton Beach Brew Station the machine made coffee just fine, it would just very slowly dispense the coffee into my coffee cup. The interior of the holding reservoir (this is where the already made coffee sits and is kept warm) was heavily stained by coffee (it was black) and the small dome shaped screen filter (this filter keeps coffee grounds from getting in your coffee cup) appeared black and clogged. I used a product called Krud Kutter available at Walmart. I poured enough of it in the holding reservoir to cover the filter and let it sit for about three hours. It now looks like new. DO NOT run this cleaner through the coffee making cycle. Dump the cleaner out and rinse the reservoir out several times with fresh water. The final step is to run a coffee cycle using just fresh water at maximum water capacity and just let it sit for a while as you would a brewed pot of coffee leaving the pot ON to keep it hot. This will allow any Krud Kutter residue to be removed.