Hampton Bay Dryers - Page 2 - Recent Questions, Troubleshooting & Support

Hi you can get help for Hampton Bay products and ceiling fans at HamptonLightingAdvice.com They also have a facebook page answering questions at https://www.facebook.com/hamptonbaylighting

Hey, hope you are doing well. I was able to source a replacement remote for you. The model number you are looking for is uc7080t for the replacement remote that works with the Harbor Breeze Yorkshire fan. https://remotecontrolplace.com/harbor-breeze-replacement-remote-controls/replacement-remote-uc7080t-for-harbor-breeze-and-hampton-bay-ceiling-fans/

This fan is also known as the Hampton Bay Covington 54 Ceiling Fan. You need to turn the globe anti clockwise until it comes out. The full instruction manual can be found here. http://lightingworldbay.com/hampton-bay-covington-ceiling-fan-54-cvt-manual/If you have another fan model other than the Hampton Bay 54CVT then try herehttp://lightingworldbay.com/hampton-bay-ceiling-fan-manuals/

Hampton Bay Ceiling Fans typically use a universal mounting system, which is compatible with most ceiling fan down rods and mounting brackets. If you have a 52 inch Hampton Bay Ceiling fan, you can use any standard mounting bracket and support bar (also known as a "J-Hook" or "Safety T-Bar") that is rated for ceiling fans up to the same weight and size. The weight of your specific fan should be listed in the product manual or on the manufacturer's website.

It's always a good idea to double-check the compatibility of any mounting hardware with your fan before purchasing, to ensure that it will provide a secure and stable installation.

www.neonlightceilingfanstyles.co.cc/hampton-bay-ceiling-fan-instruction-manuals/ - 18 hours ago

Make sure ALL screws are tight, especially the set screws. Make sure the hanging bracket is tight against fan box. If your blade arms are bent, then you need a new set. Make sure blades are not warped. Other than that you can try a balancing kit as long as it's not that last two problems listed. This happens a lot with low-end store brand fans.

For repairs and replacement parts check out Hampton Bay Replacement Parts This site is helpful for Hampton Bay products and questions.

Yes. Hampton Bay has a support number. 1-877-527-0313. Monday thru Friday, 8a to 8p EST

wobbly cieling fan1. make sure all mounting screws between the fan and the ceiling are tight. There is probably an electrical box mounted in the cieling that the fan is screwed into. I would turn the fan light on and then keep flipping breakers off, on at a time ,to see which breaker turns off the fan light. leave the fan light breaker off and you can unmount the fan from the cieling electrical box. The electrical box may have several holes in it for mounting screws and prehaps there are some holes left empty in the box that you can put more wood screws into to help keep the electrical box more firmly mounted and that may help lessen the wobble.Its ok to bend the electrical wiring aside to put more screws in. Just be reasonably gentle with the wiring and then bend it back somewhat to where it was before you started. make sure that wiring does not get pinched between the fan and the electrical box and that all wiring resides inside the box.#2 This is harder to do. you need to balance the blades for the fan ,similar to how a lawnmower blade is balanced after sharpening and before remounting the lawnmower blade on the mower. also kinda like balancing a car tire. I have a lawnmower blade balancing fixture that i bought at the lawnmower shop, but i dont know if there is a fan blade balancing fixture that you could buy from somewheres. Maybe try google.com,bing.com or ask.com and type into the search box fan blade balanceror fan blade balancing fixture or fan blade balancing jig.PLEASE read the directions or SPECIFICATIONS before you buy the fan blade balancer, only to find out that it only fits 9 inch diameter fan blades, and your blade is 2 4or 36 inches long.The balancer may have to fit a certain diameter hole at the centerof the fan blade. When you finally find out which side of the fan blade is heavy, you have to grind , with an electric grinding wheel, some material off the heavy side of the blade so that it is the same wieght as the light side of the blade.Try to imagine a cone shaped center[like step drills] like the capital letter V ,only up side down, so that the point is up. ON the underside of the inverted V is a needle tiped post that upside down V can pivot in any direction on. The hole in the middle of a lawnmower blade is centered somewheres on the outside of the inverted V, depending on the diameter of the hole in the lawnmower blade. The heavy side of the mower blade will go down and may touch the level asphault or the table top, depending on where you placed the balancing fixture. THen i would grind off metal until the heavy side can up to be level with the light side of the mower blade and it was considered balanced.an appliance repair parts store may sell fan balancers, but if the would fit your cieling fan, better ask before you waiste your money on something that wont work for what you want.Try calling up customer service of the manufacturor of your ceiling fan and ask about repair service for your brand fan.see what repair service has to say, im sure many others have asked them about wobbling fans.so they should have all the answers down pat.Two more thoughts.1. .MAKE SURE ALL SCREWS THAT HOLD FAN BLADES ON TO THE HUB ARE THERE AND are TIGHT. one loose fan blade mounting screw or one missing fan blade screw will unbalance the whole thing and cause wobble.2. the fan motor shaft bearing could be worn out or round or even egg shaped. If this is the cause, the motor must be diaassembled and new fan shaft bearings installed or the fan motor must be replaced. good luck and have fun!

If you do not have the balance kit that came with the fan, then tape a penny or nickel to the top of the blade (out of sight) that lifts the highest. Try taping the penny close into the motor first to see how it works and if more is needed, then move the coin toward the edge of the blades.

you may try different brand of led lights

RR7222T for UC7222T/CHQ7222T For Hampton Bay Ceiling Fan Remote Control ' anderic This shows 2 things, that the unit works on RADIO WAVES of 300 Mhz and that there are SWITCHES in the remote and the sensor to change the units " channels" Try another channel

I agree with Home Depot, I haven't tried calling King of Fans before. I'll have to give that a whirl! I also found this link below that has a replacement kit, they don't have the light kit though. Maybe you could ask them to add it: https://remotecontrolplace.com/universal-remote-controls/where-can-i-find-parts-for-the-hampton-bay-cameron-ii-ceiling-fan/

I recently replaced my hampton bay fan for the same reason (slow at all speeds) and discovered scorched and melted capacitors and wiring inside the fan. My suggestion is to stop using fan and replace immediately.

try downloading the manual herehttp://hamptonlightingadvice.com/hampton-bay-ceiling-fan-manuals/

Usually the capacitor has burned out, and needs to be replaced.
Try going online looking at the manufacturers site and inquiring.
hope this helps

You are just missing one wire to all the circuits. The ones that work are good ... add the one wire that is not hooking up to the others to complete a serial circuit.

Hi Bigelow,

You need two switches.  It sounds like the Electrician set up the junction box for two circuits(Lights and Fans).  i say this because your supply has 4 wires, Red , Black, White and Bare. We may be able to oversome this with one Lutron Switch. Allow me to investigate, and I will be back.

if you tell me what colors of the wires you have on the fan y what colors of the wires on the ceiling may be can help you here is my E-mail: [email protected].
have nice day