Hunter Logo

Hunter Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 553 Products
  • 9K Answers
  • 414K Views

Pull Chain on Bottom
L 1 2 3
Upper Yellow Jumper Pink Grey
Lower Orange - Jumper Black

Santa E70469

SwitchCo part # 01
or
KensElectronics.com part # ZE-208D-01

z

Hunter Dryers | Answered on Jan 13, 2020


This problem was posted on several sites, but this was the only one where I found both the cause of the problem and the solution. Mine is a Hunter 5 Minute Fan which came with no remote. And after about a month the two lights would blink together whenever I'd turn them on at the wall. So in case it helps for that type of fan or the same type of wiring arrangment here is what I did: POSITIVE SIDE: P1) Remove the light shade. P2) Remove the 3 screws that hold the cowel and lower the cowel. P3) Disconnect (pull apart) the black and red wire coupling. P4) Cut the coupling off of the black wire that comes up from the lights. P5) Strip off a quarter inch of jacket from that black wire. P6) Remove the wire nut that connects the black wire coming from the governor with the other black wire. P7) Re-use the wire nut to connect the black wire from step P5 with the other black wire from step P6. NEGATIVE SIDE: N1) Disconnect (pull apart) the white to white wire coupling. N2) Cut the coupling off of the white wire that comes up from the lights. N3) Strip off a quarter inch of jacket from that white wire. N4) Remove the wire nut that connects the white wire coming from the governor with three other white wires. N5) Set the governor aside (or just throw it away). N6) Re-use the wire nut to connect the white wire from step N3 with the other white wires from step N4. That's all, you're pretty much done! Turn on the power and test the light. If all is good, re-install the cowel and the light shade.

Hunter Dryers | Answered on Jan 01, 2020


fixya does not sell Hunter filters.

Hunter Air... | Answered on Dec 26, 2019


Likely the capacitor pack is kaput but can be other. Tjese can be found on eBay or Amazon. Capacitors are model specific.

Be sure reverse switch is not mid position. Check for power at fan pull chain.

Hunter Dryers | Answered on Dec 14, 2019


To change the time, press Hour once. Then press and hold Hour to until it reaches the correct one (pay attention to the AM/PM notation). Do the same with the Min and Day buttons. Press Return when done. (The thermostat will leave return to the normal mode after 10 seconds without a button press.)

Now to set the program, set the switch to heat or cool depending on which you want to program first. Press Prog (this will program M-F settings) then press and hold Hour until the time you want Prog 1 to start. Press the Up or Down arrows to get to the temperature you want to reach and stay for this period. Press Prog again and use the Hour/Min/Up/Down keys to set the time and temperature for next period. Repeat for program 3 and 4 for weekdays. Press Prog again to do the same thing for the 4 possible weekend program segments. Any time left at 0:00 results in a program being skipped.

Press Prog to set the Program. These settings will not take effect until the next time change in the program. You can review the settings by pressing Prog and scrolling through the settings.

Change the switch to the other setting and repeat the programming if your system has both AC and heat.

If you want to press the AutoProg button the thermostat will use preset times and temperatures. For Heating that is 5 am 68, 7 am 60, 3 pm 68, 10 pm 62. For cooling it is 5 am 78, 7 am 85, 3 pm 78, 10 pm 82.

For more information, you can get the manual from Hunter: http://www.hunterfan.com/Support/Manuals-and-Parts-Guides/ , just enter the model number in the Search line.

I hope this helps.

Cindy Wells

Hunter Heating &... | Answered on Dec 05, 2019


i don't know. battery may be dead in remote or in wrong way. please check batteries. if all tests ok, consider another remote at <https://www.ebay.com/itm/Hunter-Universal-Ceiling-Fan-Remote-Black-Receiver-K5579-01-NEW-/383158875857>

Hunter Dryers | Answered on Oct 29, 2019


Hi, hunter fan glass replacement can be found at amazon, take a look here and chose: Amazon com hunter fan glass replacement. Regards. Donald

Hunter 52"... | Answered on Oct 07, 2019


If remote and receiver is rated for fan load then this should be possible. Will need to replace remote and sensor units as 3rd party remote may not be compatible with the Hunter type.

Hunter Dryers | Answered on Oct 03, 2019


Can be almost impossible to determine code without sighting receiver. Do you have old transmitter as the correct dip switch settings would be on this. One "trick" you can do if there are more than one remote fans installed is to check other controllers for their codes. generally when installers set dip switches for multiple fans in homes they move the No1 switch from 0 to 1 or vice versa, then the switch position for second fan is move switch 2 as previous. You may be lucky and "jag" the position otherwise you will need to get to receiver.

Hunter Dryers | Answered on Oct 03, 2019


Is there power at fan terminals? If not then fan controller faulty. If yes then internal wring faulty and replacement necessary as not a repairable item. Also check if active and neutral are available at fan. Also if remote check batteries in remote unit or could be faulty remote receiver

Hunter Dryers | Answered on Sep 17, 2019


I DON'T KNOW. IF FAN HAS PULL CHAINS, PLEASE CHECK TO SEE IF THEY ARE IN ON POSITION AND TRY REVERSING DIRECTIONS A FEW TIMES.

Hunter Dryers | Answered on Sep 06, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Hunter Experts

Tom Chichester

Level 3 Expert

55370 Answers

Brad Brown

Level 3 Expert

18139 Answers

ray gallant

Level 3 Expert

66159 Answers

Are you a Hunter Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...