Konica Minolta bizhub - Recent Questions, Troubleshooting & Support - Page 3

Most likely there is paper stuck in the very back behind one of the trays. Take both trays out and see if there is any paper jammed (could be a small piece). Put trays back in but leave them open, turn off the printer, unplug it, wait 5 minutes, plug it back in, turn it back on and push in the trays.

I had the same issue and fixed it by adding the group "Everyone" to the shared folder permissions (where I was sending my scans) and assigning the "Everyone" group rights to "change" and "read".

I can even reach the "service mode".
The screen shows the error (c2557) and I can not access to anyother function.

I know this is and old post, but I came across this issue today and this post is the first that came up in my Google searches, and three was no good response. So I thought I would post an update.[Sorry Zaheer, I know you were trying to be helpful, but your response was a little too vague and in the end, inaccurate]1) Go to the printer's Web Connection by typing the IP address in a browser. 2) Make sure you are on the "System" tab (Blue) at the top3) Click on the "Detail" link on the side menu4) Click on the "Interface Info" sub link* Notice that you do NOT log into the Admin portion of the Web Connection. That will only confuse you.This will show various stats, one of which is the MAC Address of the machine. It seems like this would be better placed in the Network tab under the admin interface, but here it is.Hope this helps someone.

Try 12345678.  That worked for me for my Bizhub C250.

C-2451 to C-2453 error codes are lit even if the Developing Unit, developer, and Charging Unit are replaced. This is a symptom from a customer who mostly prints black. If you increase toner density, it will be good.

Actually C8101 is on Rank B meaning by Open / Close the front door to clear it. But if error code still appear, Check the connector between M3-relay CN5-DFCB J15 for proper connection and correct as necessary. Check the connector between PS12-DFCB J15 for proper connection and correct as necessary. Check the connector of M3 for proper drive coupling,and correct as necessary. PS12 I/O check, sensor check M3 operation check (change M3) DFCB F8 conduction check

https://printcopy.info/?mod=erc&brand=Konica-Minolta&model=bizhub+C368&code=C2552%2C+C2554

Sir/Mam, Have you had the developer and drum replaced recently, or does the screen say Replace PC Drum? There are certain house chores the copier does before "Ready to Copy" it is waiting for them to get done, so that equals "Please Wait". One big item is making sure the developer and toner are properly mixed inside the image unit underneath the drum or next to it depending on the series. Might want to have the developer replaced and drum/cleaning blade normally done all together, then run the F8 procedure/Developer Charge, and make sure the counters where cleared. Did you recently replace the drum and the developer if so did you clear the counters for the drum and developer, FIRST? IF not then the copier thinks the new drum and new developer are old. The copier works on the counters that is how it knows it got a new drum and developer. Get new developer and a new drum and have it installed correctly. Counters are clear before the unit is yanked out of the machine, then you remove the image unit/drum unit replace the developer/drum and cleaning blade. (DO NOT USE A VACUUM CLEANER WHEN REPLACING THE DEVELOPER static electricity can destroy the sensor located below the developer unit. Then reinstall and RUN F8/Developer Charge. Make sure the fax line and Ethernet cable is removed can't print anything until the F8 is run. Or you will start all over again with new developer and a new drum.

Estimated abnormal parts: • Fusing unit • Printer control board (PRCB) • AC drive board (ACDB) • Fusing heater lamp /1 (L2) • Fusing heater lamp /2 (L3) • Fusing heater lamp /3 (L4) • Temperature sensor /1 (TH1) WARNING • After replacing the defective parts, be sure to set the DIPSW 3-1 to 0. If DIPSW3-1 is set to 0 before defective parts are fixed, it may cause fire. Solution 1. Check the connection between the rear side connector of the fusing unit and the main body side connector, and repair it if any abnormality. 2. Check the connector connection and the wiring between PRCB and the temperature sensor, and repair it if any abnormality. 3. Check the connector connection and the wiring between ACDB and the fusing heater lamp, and repair it if any abnormality. (Wiring diagram: Main body (1/3): 3-E) 4. Check the installation condition of the fusing heater lamp and ON/OFF with I/O, and repair/replace it if any abnormality. (Wiring diagram: Main body (1/3): 3-D) 5. Check the installation condition of TH1 and temperature of I/O, and adjust/replace it if any abnormality. (Wiring diagram: Main body (1/3): 3-F) 6. Replace TH1. 7. ReplaceL2, L3 and L4. 8. Replace ACDB. 9. Replace PRCB.

Replace the ink cartridge.

Hi, from what I've read here: Error Codes Konica Minolta bizhub 163 , this is a Fusing Cooling Fan Motor malfunction, which suggests, I'm afraid, that you have to have it serviced. Kind regards, Jon Erik

https://www.manualslib.com/manual/1250645/Konica-Minolta-Bizhub-C360.html?page=652&term=CC172&selected=2#manual

https://printcopy.info/?mod=erc&brand=Konica-Minolta&model=bizhub+C250&code=C3751

Remove the Compact Flash Cover. Located Right side next to where the network cable is installed. Remove the cover, using a small screw driver or small plastic stick depress black button gently. Called the Warm Restart switch. When "." appears at the center on the left-hand side of the screen, enter "3" from the via 10-Key Pad. Enter the 8-digit service code and touch [END]. (Default value: 00000000) if required. Touch [Touch Panel Adjustment] from the Initial mode screen. Following the arrow mark, touch the four points (+) sequentially on the screen using a pen. DO NOT USE A SHARPE POINT!!!!!. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Hi there.
Please try .
Try this.
The error code c3451 refers to a copier warm up error; the machine had not reached the correct temp within a specific time.
I bet it happened when you first switched on one morning.
Easy to reset and fault usually goes away.

To Reset switch machine off using the switch inside the front door, not the one on the control panel.
Whilst holding the UTILITY key down on the control panel switch the machine back on keeping the UTILITY key held down. Eventually a Trouble reset key will be displayed in the LCD screen, touch this, OK will be displayed then power the machine off and then back on.

This will reset the error code, if the code reoccurs then there will be a problem with the fuser unit in the machine, and this will require replacing.

Hope it did work for you.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.

All The Best: Pineworks

My bizhub c25 jams when printing only colored photocopy. How can I resolve it pls.

Fax board error did you replace it or remove it?? was it installed ? did you install correctly there is a procedure

Self Help Product Support Konica Minolta Business Solutions Inc try this Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

bright light under the big glass is out or bad