Kyocera FS - Recent Questions, Troubleshooting & Support - Page 2

Drum unit non- installing error

The drum unit is not installed or not installed properly. You must have knocked it loose.Install the drum unit (See page P.1-5-10).

The message you get is from the fuser setting for printing envelope. At the back of the printer, you have a handle wich opens the back dor. There is located the fuser (fixing unit) that will slide back. On left and right of the fuser, you can see 2 green buttons. In your case one of them or both are pressed. If you press one time, the button goes down. If you press again, the buton rise up. Try to press them down.

Once you have installed and setup a multi-tray printer you might like to try to print a document to different printer trays. Open a word document and create a two page document.

• Select your new printer under file->Print (if it's not the default)
• Click the page layout tab
• Click the small triangle at the bottom right
• Open the page setup dialog box and click the page Paper Tab
• Choose a tray for the first page and other pages. Close the dialog box and print.

The most common machine failure codes is CF---. For example CF248, CF000. In the most cases the printer is need to be upgraded to the latest firmware.

1087 1087 163 print key

F000 is a panel communication error... update firmware... firmware as far as i know isnt available to the public... contact kyocera

Error Code 6000 is fuser code, you need to replace the fuser unit, make sure there is no paper stucking there first! I’m happy to help further over the phone at https://www.6ya.com/expert/mustafa_06f84c65ab5cc745

make sure dial on front of cassette matches paper size in cassette

LSU cleaning motor error

When the LSU cleaning motor

is driven, an error signal is

detected continuously for 1 s.

Defective connector

cable or poor

contact in the connector.

Reinsert the connector. Also check for continuity

of the connector cable. If none, replace

the cable.

Can you be more specific or provide error codes or messages?

Suggestions at the link below: Thread Kyocera FS 1035 error C7990

In some cases you can reset the C 6000 - when is a false error.
try this:
1. Go to Menu/System and browse till you see
"Service".
press and hold: # START ENTER
The "Service" will go away and browse to "Maintenance".
2. Press ENTER to go in maintenace mode - the display change to Maintenance mode.
3. browse to 0163 and press ENTER - reset fuser
4. pick EXECUTE and press ENTER
5. turn the copier OFF, wait 20 seconds and power up the machine.
If C 6000 goes away it was a false error if NO ...try again and if the C6000 persist means the thermal fuse it is blown so you have to replace the fuse = call for service.

there are many many factory modifications/bulletins for that machine, really the tru fix is very time consuming and if you are paying a dealership to repair, it will cost you more than machines value

It is calling for a maintenance kit.

call 239 939 5383 they can try to locate one for you and quote you a price for a new one

MP tray is not the cassette it this flap that pulls down above it.

The machine will revert to asking to place paper in its MP tray when the information it is receiving about the document from whatever program tell it that the size is not the same as what the cassette is set to...

so, check page size in of document in word program or whatever you are using

also check paper type and size settings match those you just checked in the printers properties under printers in control panel.

If you put a piece of paper in the MANUAL BYPASS TRAY bot the cassette it will print on that.

To get evverything back to normal, turn off printer, delete jobs in print que, change paper size of document in word/excell/etc is set same as paper type in printer, print again.. all should be good...

p.s. these are good quality printers that why I bother to answer you... cheers

push the drum unit in completely

replace fuser unit

I had the same problem. Pull the Fuser and check Conector.Sometime pieces of paper inside the Conector raises an error.

Please Rate .

i have 7410 error call service. i tried to clean everithing en replaced the tone is almost full- still getting the error message.hat can i do. (fs-3900dn)