Kyocera FS - Answered Questions & Fixed Issues - Page 9
KYOCERA FS 1370DN 7990 0088329
Empty the waste toner from the back side of the drum unit. Then remove and reinsert the waste toner sensor connector from the controller assy (main pwb).
1116 error 6400
Remove and reinsert the two connectors of the fuser unit. If not, then remove and reinsert all the connectors from the engine pwb and the power pcb.
Kyocera 1116 code 6000
Check the lamp and the thermostat for continuity. Check the operation of the thermistor. If something defective replace. Most common is the thermostat. In addition, check the operation of the cooler fan on the machine's left. If it is not working then you have to fix or replace it. The most rare but existing failure is call service 6000 due to defective power supply. In this case the heat roller is stuck on press roller.
Kyocera FS-4200DN fuser
If the heat roller is dirty with "baked" toner, first you have to clean the roller with nitrocellulose thinner and immediately upgrade the printer to the latest firmware.
What can i do with error 2250:0110409?
There is a problem with the lsu/charger cleaning motor. Maybe one of the four main charger or LSU has stuck. Check the main chargers and the LSUs if their gears rotate properly or they are stuck somewhere. Otherwise, the motor that drives the cleaners is defective. You can isolate the automatic LSU/Charger cleaning by remove the connector from the engine pwb. First you have to check if the lsu/charger cleaners are at home position or not.
6/11/2014 4:34:16 PM •
Kyocera...
•
Answered
on Jun 11, 2014
•
183 views
HOW TO RESET A KYOCERA FS-C5150DN
you can open the command center of the printer, login using the password admin00. Then go to tab "Basic", click Reset and choose the last one, which says Reset Entire Device To Factory Defaults.
If you just want to reset the frpo parameters to factory defaults, then use the command !R! FRPO INIT; EXIT;
6/10/2014 4:47:33 PM •
Kyocera...
•
Answered
on Jun 10, 2014
•
5,335 views
What is ccd in printer
Ccd: charged-Coupled Device, this part in the machine capture incoming light from scanned original and convert it into a digital signal.
6/6/2014 3:07:08 PM •
Kyocera...
•
Answered
on Jun 06, 2014
•
51 views
What do i do if u replace new toner and the message replace toner does go
Check the toner sensor under the processing unit (PU).
Remove the PU and you will see in the front left side, inside the machine, a black sensor (a black part with cross screw on it and a spring underneath it. There is a possibility that sensor to be dirty or damaged.
An important question is... is the toner original or compatible with appropriate chip (toner id)?
Resettare codice errore c6 su kyocera fs 1118
If the code is C6400, then just follow the procedure showing in the images below.
If the code is C6000, then you have to remove the fuser unit and check the thermistor, the thermal cut out and the heater lamp. If are able to fix the problem-damage, then follow the procedure below to reset the service call.
Kyocera paper jam duplexer
The duplexer unit is located at the bottom of the printer. You have to remove the paper cassette first. Second, tilt the printer a little on the back side. In place of paper cassette, you will see an iron plate with a green handle in the left. Push down on the handle and the plate will go down. You may find paper jam there or pice of paper stucked. Release the handle and put back the printer and paper cassete, then open top cover and close it down. You may have paper jammed also under developer unit, or in the fuser section. Verify there, if the first solution won't solve the problem.
Black lines on printed documents
Vertical lines? How many pages have you printed? Check the counter and then answer to my post. Maybe you will need to replace the MK. Check the surface of optical cylinder for scratches. However, if the MK is not at the end of his life, and the cylinder surface is not damaged, you will need to clean the charge roller and then to execute an Drum Refresh from Service submenu. This is the most frecvent problem that I meet, related to vertical lines. There could be other bad components, but you will need to check first the drum unit.
Not finding what you are looking for?