Maytag Neptune - Answered Questions & Fixed Issues
Maytag Neptune dryer displays 88 and won't start
our dryer just keeps running and doesnt not shut off after cycle is done. You have to unplug or open door for it to shut off. This is not a refurbished dryer we had bought brand new
2/12/2019 1:03:52 PM •
Maytag...
•
Answered
on Feb 12, 2019
•
3,317 views
Was drying a load of
Good morning to you
I would clean all the fluff from the dryer.
Enjoy your coffee
Kolbrun
1/25/2018 6:35:26 AM •
Maytag...
•
Answered
on Jan 25, 2018
•
2,142 views
What does error code U361 mean
A "U" code is a generally caused by an unbalanced load. If the dryer is level and has a medium size load causing the error, you may need to have the "Unbalance switch or control board" replaced. As with any electronics, unplug it for a few minutes to reset it and try again.
10/28/2014 9:42:02 PM •
Maytag...
•
Answered
on Oct 28, 2014
•
111 views
Maytag MDE2400AYW Dryer Heating Elements not staying on
i am sending you all the possibilities for your problem, check either of these causes ----and than let me know if it is solved----
Power from the house
Check to see whether there's power getting to the dryer. Is it plugged in? Check for blown fuses or tripped circuit breakers--your dryer uses two fuses or circuit breakers. The dryer could tumble but not heat if only one of the two fuses is blown. If you have circuit breakers, one of the two circuit breakers can trip, even if the two for the dryer are connected.
Heating element
Often a dryer heating element burns out, but doesn't trip the circuit breaker or blow a fuse. The heating element is simply a long coil of special wire. You can check it for continuity with an ohm meter. No continuity means the element is bad and you need to replace it--electric heating elements aren't repairable.
Thermal fuse
On many dryers, there's a thermal fuse mounted to the exhaust duct inside the back cover panel. The fuse--which is about an inch long--is usually embedded in black resin and mounted in a white plastic housing. If the fuse has blown, you need to replace it. (You can't re-set it.)
Wiring
A common problem is for the main wiring connection from the house, at the dryer, to burn and break its connection. Because the dryer can still tumble with partial power, the connection may be only partially defective. You may need to replace both the power cord to the dryer and the terminal block inside the dryer that the wire is attached to.
10/24/2015 11:45:25 PM •
Maytag...
•
Answered
on Oct 24, 2015
•
3,472 views
My Maytag Neptune is making a banging sound while
Hi,
Here is a tip that I wrote about dryers and noises...
It will help you determine what is happening there...
Dryer Repair Squeaks, Grinding, Clicking and Knocking Noise
heatman101
Asker's Testimonial "That answer was very informative - thank you for taking the time to educate me. " - teresa241964
1/12/2011 5:54:53 PM •
Maytag...
•
Answered
on Jan 12, 2011
•
259 views
Maytag mde2400azw takes forever to
Hi,
If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.
if you dryer is gas check out this gas no heat tip....
If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.
check out this electric no heat tip...
heatman101
12/27/2010 6:31:08 PM •
Maytag...
•
Answered
on Dec 27, 2010
•
513 views
My dryer gives a 3Ecode
3E == overcurrent detected at the motor.
Open the control panel, there should be a tech sheet in there that explains how to put the machine into service mode (presschimeandextra rinsekeys for three seconds) and what to do while in service mode to track this down. Once on service mode, you can cycle through and retrieve all diagnostic codes... and lots of other stuff that'll help you track this down.
You can also go ahead and check out the windings on the motor. Unplug harness connector and test from wire insertion side.
Pin #1 and Pin #2 of CN9 == 11.6 ohms
Pin #1 and Pin #3 of CN9 == 11.6 ohms
Pin #2 and Pin #3 of CN9 == 11.6 ohms
11/26/2010 9:42:31 PM •
Maytag...
•
Answered
on Nov 26, 2010
•
459 views
I have a maytag neptune dryer and the drum is
Why do you say that the drum is loose? Are you able to wobble it by hand? If so, that is evidence of a bad roller that the drum sits on.
If the drum doesn't turn as fast as it did, that is probably a loose belt, which would indicate that the belt tensioner is not working or belt has jumped the tensioner.
6/13/2010 2:17:41 PM •
Maytag...
•
Answered
on Jun 13, 2010
•
521 views
How do I access the drum to tighten the dryer fins
Disconnect power to the dryer !!! Remove the 2 screws holding the door hinges on and remove the 2 screws opposite the door hinges . This will let you pull the top of the front panel outward and lift off the bottom clips . If you have enough room , slide your arm thru the front opening to tighten the screws . Otherwise , remove the 2 screws holding the clips for the top , 1 on each side , and lift the top , to get better access to the screws .
4/10/2010 10:28:01 PM •
Maytag...
•
Answered
on Apr 10, 2010
•
479 views
No heat in dryer
check your house fuses or circuit breaker.a dryer needs 240v to heat if you loose a line (120v) it will still run but without heat
2/6/2010 6:32:44 PM •
Maytag...
•
Answered
on Feb 06, 2010
•
397 views
Front load MDE2400AZW takes forever to dry stuff.
Make sure the lint trap in the door is clean. It has a plastic cover that opens. Disconnect the venting at the rear and run a load, if it works you have a restriction in the hose after the dryer or in the wall past the hose.
1/5/2010 10:54:15 PM •
Maytag...
•
Answered
on Jan 05, 2010
•
1,174 views
Not finding what you are looking for?