Wont drain and spin
65mungus
You have clutch malfunction. Take a look at my Clutch Fix post and see if you can DIY the fix.
Basic hand tools and DIY skill sets is all that is required and you can save your $1K machine. Post back if you have questions or concerns…..Rich
Freezer part works but not fridge
The circulating fan(Freezer Fan) supplies air to freezer as well as the refrigerator. As the DC brushless motor wares out the rpms reduce to a point that it is hard to diagnose. This motor alone costs around $80.00(appliancesfactoryparts.com) Replacement of the fan motor is labor intensive to remove fan assembly because the electrical connections are at the exteme rear of the freezer compartment
10/13/2022 7:57:04 AM •
Maytag...
•
Answered
on Oct 13, 2022
Dimensions on a Maytag lse7800acw
Thanks for question. I have found your model dimensions
Width: 27 1/2 Inch
Depth: 27 1/2 Inch
Height: 73 Inch
Washer Capacity: 7.2 Cu. Ft.
10/3/2022 5:54:08 PM •
Maytag...
•
Answered
on Oct 03, 2022
What is an error code 10 on a Maytag Neptune dryer?
The electronic control panel and board has detected a runaway in the temperature and the control board and the heating sensor could be broken on your dryer and need to be replaced.Or the circuit breakers may need replacement then.
How do i reprogram my HV board?
HERE TIS RIGHT OFF THE INSTRUCTION SHEET. THE TECH JUST LEFT. POWER UP REF. PROGRAM CODE IS LOCATED ON SERIAL PLATE ON THIS UNIT AFTER THE WORD CODE.-1. PRESS & HOLD THE DOOR ALARM KEYPAD.-2. PRESS & HOLD FREEZER TEMP DOWN KEYPAD.-3. RELEASE DOOR ALARM KEYPAD AND WAIT 3 SECS.-4.CONTROL WILL DISPLAY PE TO INDICATE PROGRAMMING MODE-5. ENTRY IS CONFIRMED BY PRESSING TEMP DOWN - KEYPAD ONCE MORE.-CONTROL WILL DISPLAY CURRENT PROGRAM CODE. THIS VALUE SHOULD BE VALIDATED THE THE PROGRAM CODE PRINTED ON UNIT SERIAL PLATE.-NOTE: IF PROGRAM CODE IS CORRECT, THE PROGRAMMING MODE IS EXITED BY CLOSING THE FRIG DOOR.-7.PRESS REFRIG TEMP UP KEYPAD + OR REFRIG DOWN KEYPAD -TO CHANGE THE DIGIT VALUE WITH EACH KEY PRESS.-8.THE DECIMAL POINT INDICATES THE SELECTED DIGIT. PRESS THE FREEZER TEMP UP KEYPAD + TO SELECT NEXT DIGIT.-9.ONCE DEIRED PROGRAM CODE IS DISPLAYED, PRESS AND HOLD THE FREZZER TEMP DOWN KEYPAD - UNTIL UNIT PROGRAM CODE BEGINS FLASHING INDICATING IT HAS BEEN SAVED. *note* IF YOU ATTEMPT TO ENTER AN INVALID PROGRAM CODE, THE CONTROL WILL NOT SAVE THE NEW CODE, BUT WILL BEEP! (THE UNIT WILL NOT RUN RUN WITH A UNIT PROGRAM CODE OF 0000). ONCE THE PROGRAM CODE HAS BEEN SAVED THE PROGRAMMING MODE IS EXITED BY CLOSING THE FRIG DOORS.
9/7/2022 1:58:32 AM •
Maytag...
•
Answered
on Sep 07, 2022
Maytag stackable MLG2000AWW - washer door won't open
You will have to call a person that repairs major appliances to have a look and see what the problem is. There could be something wrong with your washing machines controls for the door not to open at all. Or the door latch could be the problem and the motor.
MEW6527DDS oven: some keypad buttons have stopped
(I'm providing a late, modern response for people like me who land here in 2022+)
I had the same problem. Gradually it got worse until only Bake ' Cancel work. Sometimes the problem is due to bad ribbon cable connections; sadly, with this oven, the issue is the membrane buttons having failed. It's frustrating, because this has happened with every version of this model that I have seen. Add to this that the membrane buttons are behind a sealed panel that you can't access without breaking it, and you'll quickly learn that you need to buy the replacement part. 5765M483-60 is the matching control unit, but make sure with the vendor that it is the right size for your unit first; it's expensive. It's also now out of stock and is a 2-3 month special order at most vendors. The replacement is tedious, but simple and approachable for a first time DIY'er. At this point, I'd rather buy a new replacement oven instead, but finding 27" models is difficult as most are 30" now, which won't fit my cabinetry - thus I bit the bullet and bought the replacement control unit. Oven came with the house on purchase; former owner told me she had already done the same repair once before; so that means this problem will keep recurring.
8/28/2022 9:19:59 AM •
Maytag...
•
Answered
on Aug 28, 2022
Not finding what you are looking for?