Maytag Popular Questions, Answers, Tips & Manuals

Sometimes you can bypass the lock although it is not recommended. You should be able to get the lock in 2 days. https://www.google.com/search?q=Maytag+Neptune+mah5500bww+door+lock+bypass ..

Possible bad tooth in the timer gears. Replace the timer. Be sure to take a few snapshots with a phone in case you get wires mixed up Mark same color wires and replace them one by one. (BE SURE TO UNPLUG UNIT BEFORE CHANGING TIMER!)

If your Maytag washing machine is making a loud noise during the spin cycle and is not draining the water, there are a few possible causes. Here are some steps you can take to troubleshoot the problem:

1. Check the drain hose: Make sure the drain hose is not clogged or kinked. If the hose is clogged or kinked, water may not be able to drain properly.
2. Check the pump: The pump is responsible for draining the water from the washing machine. If the pump is not working properly, it may be making a loud noise and not draining the water. You can check the pump by removing the front panel of the washing machine and locating the pump. Check for any visible damage or obstructions.
3. Check the belt: The belt is responsible for turning the pump. If the belt is worn or broken, the pump may not be able to drain the water properly. You can check the belt by removing the back panel of the washing machine and inspecting the belt.
4. Check the bearings: The bearings are located in the drum of the washing machine and can wear out over time, causing a loud noise during the spin cycle. If the bearings are worn out, they will need to be replaced.

If you are not comfortable troubleshooting the problem yourself, you may want to contact a professional appliance repair service for

It's possible that the issue is with the control board and not just the control panel. Before replacing the control board, here are a few things you can check:

1. Make sure the control panel is properly connected to the control board. Check the connections and make sure they are secure.
2. Check for any damaged wires or connectors. Look for any signs of damage, such as frayed wires or loose connectors.
3. Check the voltage to the control board. Use a multimeter to check the voltage at the control board. If there is no voltage, there may be an issue with the wiring or power supply.
4. Check the fuses on the control board. If the fuses are blown, the control board will not function properly.

If none of these steps resolve the issue, it's possible that the control board is faulty and needs to be replaced. However, it's important to note that diagnosing and repairing electrical issues can be dangerous and should only be attempted by qualified professionals. If you're not comfortable working with electrical components, it's best to seek the help of a certified technician.

This issue could be caused by a number of things. It is possible that the clothes are not properly balanced in the wash drum, causing them to wrap around the agitator. It could also be a problem with the agitator itself, or with the transmission.

Try unplugging it or turn off the breaker to it for 60 seconds to see if it'll reset.

Water collecting and freezing on the floor of your freezer compartment is likely due to a clogged or frozen defrost drain. When the refrigerator goes through a defrost cycle, the melted ice and frost should drain through the defrost drain and into the drip pan underneath the refrigerator. However, if the drain is clogged or frozen, the water will collect on the freezer floor and eventually freeze. To fix this issue, you will need to clear the defrost drain. Here are the steps to do so:

1. Unplug the refrigerator to avoid any electrical hazards.
2. Locate the defrost drain at the back of the freezer compartment. It may be covered with ice or debris, so you may need to remove the freezer drawer and any shelves to access it.
3. Clear the drain using a turkey baster or a small funnel to pour hot water down the drain. You can also use a pipe cleaner or a wire to remove any clogs.
4. Once the drain is cleared, you can clean the inside of the freezer with a solution of warm water and baking soda to remove any odors.
5. Finally, plug the refrigerator back in and allow it to cool down before placing the food back in the freezer.

If you're unsure about performing these steps, or if the issue persists after clearing the drain, it's best to consult a professional appliance repair technician to diagnose and fix the problem.

A squealing noise during the sensing cycle of your Maytag top-load washer can be caused by a number of factors. Here are some common reasons and steps you can take to resolve the issue:

1. Loose belt - The noise could be caused by a loose or worn belt that needs to be tightened or replaced. You may need to remove the front panel of the washer to access the belt.
2. Idler pulley - If the idler pulley that keeps tension on the belt is worn or damaged, it can cause a squealing noise. Replace the idler pulley if necessary.
3. Bearing - A worn bearing in the tub can cause a squealing noise. Replacing the bearing will typically require disassembling the washer.
4. Drive motor - If the drive motor is worn or damaged, it can cause a squealing noise. Replace the drive motor if necessary.

If you're not comfortable diagnosing and repairing the issue yourself, it's best to contact a qualified appliance repair technician for assistance.

Locks wear out because they get so much use and are solenoid controlled. Just replace it.

It is likely to be a failed control board. They are expensive so call for service. Then you get the correct diagnosis and warranty on the part and the labour. https://www.google.com/search?q=maytag+bravos+washer+powers+on+and+then+off ..

If you have cleaned the drain pump of your Maytag washer model MAH8700AWW and it is still leaving a small amount of water in the tub after the drain cycle, this may be causing the nd error to show up. One thing you can do is to check the drain hose to make sure it is not kinked or obstructed, as this can also cause the washer to not drain properly. If the drain hose is clear and there is still water remaining in the tub after the drain cycle, you may need to check the drain pump itself to make sure it is working properly. It is also possible that there could be a problem with the water level switch or the control board, but you have mentioned that the board tests good according to the troubleshooting book included with the washer. If you have tried these steps and the issue persists, it may be necessary to consult a professional technician to diagnose and repair the issue with your Maytag washer.

The rubber boot takes up that space unless the suspension/bearing is damaged, in which case, I would have it serviced.

There are several potential reasons why your Maytag Gemini double oven electric range is still not heating up after replacing the bottom element and thermal sensor and testing the power. Some possibilities include:

1. The wiring or control board may be faulty and preventing the oven from heating up.
2. The upper heating element or broil element may also be faulty and need to be replaced.
3. The oven may not be calibrated properly, which could cause it to not heat up correctly.
4. There may be a problem with the oven's door latch or switch, which could prevent it from heating up.

Holding the Cycle End Signal button for 3 seconds is the way to turn the control lock off and on with this model. If that is not unlocking the control like it should, the first thing you would want to try is unplugging it for 5 minutes to let the controls reset. Best to you

I'm sorry but I'm unable to find the cubic feet size of Maytag dryer model SDG515DAWW. However, you may be able to find this information on the Maytag website, in the product manual, or by contacting Maytag customer service. Additionally, you can measure the interior dimensions of the dryer to estimate the cubic footage. The interior width, depth, and height measurements, when multiplied together, will give you an estimate of the cubic footage.

It is possible that the power outlet the washer is plugged into has lost power. Check to see if the outlet is working by plugging in another device. If the outlet is working, then it is possible that the power cord has become loose or disconnected. Check the power cord to make sure it is securely plugged into the wall and to the washer. If the power cord is securely connected, then you may need to call a professional to diagnose and repair the issue.

Here you go...watch the video on how to replace the timer... https://www.repairclinic.com/Shop-For-Parts/b4/Maytag-Parts?query=MSD2654FR&searchwithin=defrost%20timer

I would remove the track, clean both surfaces and stick it with clear silicone or superglue Gel. Leave it 24 hours to set.

es, in order to remove the top of a Maytag LSE1000 washing machine, you'll need to first disconnect any attached wires. This is because the wires are connecting important components like the control panel and the sensors to the rest of the machine. Here are the steps you can follow to safely disconnect the wires:

1. Unplug the washing machine: Before you begin, make sure to unplug the machine from the power source to prevent any electrical shock.
2. Locate the wires: Look for the wires that are connecting the top of the machine to the rest of the machine. They should be near the back of the machine where the top and bottom halves of the machine meet.
3. Label the wires: Label the wires so you know which wire goes where when you're ready to put the machine back together. You can use masking tape and a marker to label each wire.
4. Disconnect the wires: Gently pull the wires from their connectors, making sure to keep them separated so they don't get tangled. Be careful not to pull too hard, as this could damage the wires or the connectors.
5. Repeat the process for all the wires: Repeat the process for each wire until they're all disconnected.

Once you've disconnected all the wires, you should be able to remove the top of the machine. Make sure to keep the wires organized and in a safe place while you're working on the machine. When you're ready to reassemble the machine, simply reconnect the wires in the reverse order you disconnected them.

If your Maytag MDE4658AYW electric dryer is running hot on all settings, even on air fluff, it is likely that the heating element is not working properly. Make sure that the heating element is securely connected to the dryer and that the power switch is in the "on" position. If the problem persists, you may need to replace the heating element or contact the manufacturer for assistance.