Maytag Logo

Maytag Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 2K Products
  • 163K Answers
  • 3M Views

I am unfamiliar with your machine. It is usual the tub drain is at the lowest part of the tub and the pump is below. This means if there are no blockages, a weight of water is always present at the pump impeller so a simple pump can be used and no priming is necessary

Generally the arrangement of hoses, the drain and pump is so simple if there are no blockages and the pump is in good order and running, pumping is inevitable.
A blockage of the drain or of the outlet hose isn't unusual...

Maytag Washing... | Answered on Jun 28, 2019 | 55 views


Worn out drum Bearing can cause vibration and make the spin cycle very noisy.

Maytag Washing... | Answered on Dec 06, 2019 | 2,366 views


It could be the start relay on the compressor failing. If the fridge cant get down to temperature, the icons or alarms will start to flash or beep.

Maytag... | Answered on Jun 16, 2019 | 71 views


Pull the toe kick plate straight off the front to gain access.

The pan is located under the freezer and accessed by pulling it out from the front (not attached, just sits in place.)

Maytag... | Answered on Jun 16, 2019 | 58 views


The puff sound you hear is the "Ignition" its normal, all stove is like that if you not hear it the oven will not work.

Maytag Kitchen... | Answered on Jun 14, 2019 | 73 views


It sounds like the clutch has seized. Have a look under the machine, a telltale sign is lots of brown / black greasy marks all over the inside of the cabinet and on the floor. If the machine is still spinning but "ratchetting" on wash, it is the clutch that is not releasing.

Maytag Washing... | Answered on Jun 10, 2019 | 218 views


I DON'T KNOW. PLEASE CHECK FUSE OR CIRCUIT BREAKER FOR WASHER. IF OK, MOVE BREAKER TO OFF AND ON A FEW TIMES. LOOK TO SEE IF YOUR WASHER CONNECTION IS A 110V PLUG THAT IT IS
FIRMLY PLUGGED IN. THE DOOR SWITCH MAY BE LOOSE OR HAS FAILED. IF POSSIBLE LEAN ON THE
DOOR WHEN CLOSED TO SEE IF PANEL COMES ON.

Maytag Washing... | Answered on Jun 10, 2019 | 54 views


First step is similar to a computer. Reboot. Turn off your dishwasher at the breaker box. Hopefully your electrician designated a separate breaker for your dishwasher, otherwise whatever else is on that breaker will be off. Shut the breaker off; wait 10-15 minutes; turn breaker back on. This will resolve many issues and is the first step to try.

Maytag... | Answered on Jun 08, 2019 | 80 views


In a Home the recommended level (front higher to back lower) is 1/4" (Right to Left - level)
Never less than in order to allow door to shut own their own, but there is nothing wrong with having a perfect level refrig if everyone closes the doors properly which they won't. A refrigerator requires to be reasonable leveled to avoid compressor fatigue. In a Motorhome people can't always find level ground, so it quite frequent that their refrigerator burns up when running. From that experience I'd say I would level any fridge which is over 1/2 inch off.

Maytag... | Answered on Jun 08, 2019 | 7,557 views


The water is coming from the air that is being cooled. This how AC work. Refer to instructions that came with unit for further explanation.

Maytag... | Answered on Jun 07, 2019 | 49 views


Request directly from Maytag

Maytag Washing... | Answered on Jun 06, 2019 | 604 views


Lid closed safety switch is bad.....it must be in a normally closed condition to go to spin and rinse cycle.....You can jumper the switch........That will allow spin with lid open so be careful..............

Maytag Washing... | Answered on Jun 06, 2019 | 85 views


I am not familiar with the model but the lid switch typically would have nothing to do with preventing the programmes advancing; the lid switch is typically a safety device to prevent personal injury to the unwary by denying them access to moving parts.

Your description indicates all the aspects of the wash functions are present and working which indicates the problem probably lies with the main controller.

Maytag Washing... | Answered on Jun 07, 2019 | 74 views


maytag is correct the water in the filter freezes and expands and breaks the filter at the weakest point which is the seam other locations are at the mounting connection and units that have water line in door the T connection inside door

Maytag... | Answered on Jun 04, 2019 | 38 views


Hi Kim, what you need to do is lean the washer back to see where the leak is coming from. It could be a split hose or a damaged tub. You could also have a bad tub seal. If it's not easily visible,you may need to call a local repair company. Hope that helps.

Maytag Washing... | Answered on Jun 04, 2019 | 98 views


It is under warranty, either call for service or return to place of purchase for another one. Warranty repairs are at no charge.

Maytag Dryers | Answered on Jun 04, 2019 | 52 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Maytag Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Brad Brown

Level 3 Expert

18157 Answers

Cindy Wells

Level 3 Expert

6068 Answers

Are you a Maytag Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...