Minolta Office Equipment & Supplies - Page 3 - Recent Questions, Troubleshooting & Support

M2 Call service.Maintenance M2, M1 Call service errors.To remove this error do the following steps.1-Press utility button on panel.2-Now press these buttons one by one, Press Stop, then zero, again zero, then stop,then press zero.3-its the code to get into service mode.4-After pressing above mentioned buttons you will enter into service mode.5-Now select service choice option.select it by pressing OK button.6-In service choice option you will see Maintenance count option.7-Select it by pressing Yes or OK button.8-There will be three options 0,1,2.9-Select 1, it will show a new menu, with numbers, now press C button to clear the counter.After the counter is cleared.Select 0 and press Reset button.

Have you replaced the image units and toner units with OEM parts Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

First copy slow generally next copy ok

Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA so please make sure. SportzCraazy Get all the Live Updates and Latest Sports News

Procedure for Installation of Hard Disk in Konica Minolta bizhub 283/363/423 Photocopier Machines, 1-Get a SATA hard disk. NOTE: SATA HDD is supported in the above mentioned models. IDE or PATA are not supported.So get a SATA HDD. SATA HDD have two main connectors. 1 is for Data and the other one is for power as shown in the image.Two separate cables are used.Data cable and the power cable.Get both the cables.Image of the cable is shown below. Data Cable for SATA Power cable for SATA Hard Disk 3-Connect the cables in their respective areas. 4-Now place the hard disk on its fitting. HDD mounting kit is fitted at the main control board of the machine.For this, open the back side cover of the machine and you will get the fitting.It will be on the main board in front of you. Now fit the HDD on its mounting and tight the four screws at its sides to keep HDD safe from shocks / jerks. 5-Now connect the data connector and the power connector to the control board.There will be two separate jacks for power connector and the data connector. 6-After fixing both the connectors to the main board, close the rear cover of machine with the screws. 7- Now turn the machine ON. 8-Go to the service mode and click on "SYSTEM 2" 9-Now click on "HDD" and select "ENABLE" and press "OK" 10-Now click on "state confirmation" 11-Select "HDD" 12-Now click on Format Hard disk.Select "Logical Format" not the physical format.Press "START" button and wait for few minutes. 13-When formatting is finished press "OK" and restart the machine. 14-Your new HDD installation is complete now and its ready to use for box operations.

(TABP0902037EN00) - magicolor 2200 DeskLaser - What are the steps to fix a service call 16H transfer belt rotate error on a magicolor 2200 series? (TAUS0805552EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'ACC_Getstatusr EC;Code=__D, Resetting ACC to Initial State' (q0601101) (TAUS0805008EN00) - magicolor 2 + - Installing CrownNet code on the Crown monochrome printer (q0499042) (TAUS0803976EN00) - magicolor 2200 + - Flashing System Code to DeskLaser to Correct 'Starting System Firmware Image' Message (q0202107) (TAUS0806277EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Toner Missing' (q0800700) (TAUS0806280EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Transfer Belt Missing' (q0800703) (TAUS0806281EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Fuser Missing (q0800704) (TAUS0806282EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Oil Roller Missing' (q0800705) (TAUS0806283EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Toner Low' (q0800706) (TAUS0806284EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Toner Empty' (q0800707) (TAUS0806286EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Replace Fuser Unit' (q0800709) (TAUS0806287EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Transfer Belt Life Low' (q0800710) (TAUS0806288EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Replace Transfer Belt' (q0800711) (TAUS0806289EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'OPC Drum Life Low' (q0800712) (TAUS0806290EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Replace OPC Drum' (q0800713) (TAUS0806292EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Replace Waste Toner' (q0800715) (TAUS0806293EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Oil Roller Life Low' (q0800716) (TAUS0806294EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Replace Oil Roller' (q0800717) (TAUS0806295EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Put Media in Input Tray' (q0800719) (TAUS0806296EN00) - magicolor 2200 + - Clearing MC 2200/MC 2210 Status Messages or Error Codes 'Put Media in Upper Bin' (q0800720)

Replace the print head.

Clear the maintenance counter in service mode.

Please explain (Stating (!) memory Free 99 0/0????????

Has the drum, developer and cleaning blade been replaced? If So Touch Counter, Stop,0,0 Stop 0,1. Then select Counters and select PM and clear.

Mazidul Islam
8724875511

For that you have to open copier back cover then you can see fuser unit. You need to clean and do some servicing on fuser unit Also clean sensor then reconnect fuser assembely then check. Also make sure there is not any paper jam clean dust and ink from all parts try with another toner cartridge. Then check. Let me know if you need further assistance. Thanks for using FixYa.

https://manuals.konicaminolta.eu/bizhub-C287-C227-UD/EN/contents/id16-_102039157.html https://www.konicaminolta.com/healthcare/catalog/pdf/manual_drypro_sigma2.pdf

Take this to a dealer or repair service. Electric shock hazard can spoil your day and/or end your life.

If you did not choose single color. Occurs from several devices. laser Unit. Mainboard. Hv Board.

Since the machine is a production print type machine you may want to have a tech come out as removing the fuser / Fixer (The Heating Unit) can take some doing and the cause of the jamming many.

http://www.fixya.com/answer/answerpageslideview.aspx?thid=27174806&ctg=459&brd=1104 Read and attempt the published solution. Semper Fi Z

Requires removal of the drum and developer unit 2 small screws and the large one in the middle. which holds a locking device. Then remove the charge corona assy. developer unit. Replace the drum with a new cleaning blade. Ensure the Drum Density sensor is cleaned. And Paper Jam senor. As you can see its not easy. recommended a tech. or purchase download service manual.