Mitsubishi Logo

Mitsubishi Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 2K Products
  • 179K Answers

Hi! Have fuso fighter which am repair engine but the timing confused the engine is 6m61

Mitsubishi Cars... | Answered 13 hours ago

there is a bad sensor or broken wire on the safety restraint system.... it needs to be scanned so you know which sensor is bad or broken wire....

Mitsubishi Cars... | Answered Yesterday

The idle air control is attached to the throttle body, located between the air cleaner and the intake manifold, and held on with 2 or 3 small screws. You should clean this, and the throttle body with carb cleaner while it is apart and try to resurrect.

2005 Mitsubishi... | Answered on Feb 14, 2020

Corrupted firmware. If you wish to get some details; check the site linked here. Pull up older posts.
Line, faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent.

Mitsubishi... | Answered on Feb 12, 2020

Main digital board fault. Do not try to repair this TV; if you are not qualified, and haven't enough experience in servicing. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.

Mitsubishi... | Answered on Feb 12, 2020

Here is a question that we see often.


I've replaced everything in my television because it previously had a black screen with no lighting. Now it doesn't turn on at all and all I have is audio. What could be the cause ?

So your television stops working properly and you think it must be easy to fix, because you can buy boards on eBay, and you can watch YouTube videos. So you make a decision, you buy a board and you fit it, but the television still doesn't work! This is a classic case of the 'let's try replacing this' method of television repair and illustrates why it is a bad idea. It doesn't work for a number of reasons. To correctly diagnose issues, you need to know every board, what is does and every component on the board. You need to know which part has failed, replace the component, or replace the board. The parts you purchased off eBay were probably out of scrapped sets and not tested. The part your put in was dead when you put it in, so you just moved on to another guess at what might be the cause and replace a board that is fine. And so it goes on, you change all the boards and it still doesn't work. Did you notice the large print that says 'No Refunds, NO Returns'. This is to stop you sending your old one back and saying it didn't work, but the unscrupulous use it as an excuse to get money for selling items that may not work! The course to be a television engineer is 2 years full time education, take it to someone that knows how to diagnose and fix. It is by far the cheapest option. The part that failed might be a 20 cents fuse diode hard soldered to a board. They will charge you $2 parts and an hours labour.

Mitsubishi... | Answered on Feb 11, 2020

Hi, Stacy for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Mitsubishi, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.

Mitsubishi Cars... | Answered on Feb 06, 2020

I suspect your parking brake has expanded due to use and now is preventing the removal of the discs. Loosen the parking brake cable to allow the parking brake pads to fully retract. Then they should come off. When installing the new discs, be sure to re-adjust your parking brake so it actually engages when applied.

Mitsubishi Cars... | Answered on Jan 31, 2020

The firing order should be 1 2 3 4 5 6
Your cylinder banks are odd and even numbered.
Looking under the hood, front bank of cylinders , from left to right, 2 4 6
The rear bank of cylinders, left to right, 1 3 5

Mitsubishi Cars... | Answered on Jan 30, 2020

If the status LED shows a consistent green light it means that the power is on, on the TV. ... If the status LED is blinking yellow, that means the lamp cover is open. If the status LED is blinking red and then blinks yellow, that means you will need to follow that code to find the problem with the TV.Aug 14, 2013 > watch

Mitsubishi DLP TV Repair - TV is Blinking - How to Identify ...

Mitsubishi... | Answered on Jan 23, 2020

I know some models have a square panel you remove on drivers side to get to one fuse box and some have fuses behind the glove box.

Mitsubishi Cars... | Answered on Jan 19, 2020

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

85223 Answers

The Knight
The Knight

Level 3 Expert

76237 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides