Try connecting a cable directly from your router to your laptop and using the actual IP address of your router instead of routerlogin.com, being a Netgear it should be 192.168.1.1 or 192.168.0.1. Hope this helps.
To access the router:1. Type http://www.routerlogin.net in the address field of your browser, and then click Enter.2. When prompted, enter admin for the router user name and password for the router password,both in lowercase letters. (For security reasons, the router has its own user name andpassword.)3. On the main menu, select Wireless Settings to display the Wireless Settings screen.Note that the default SSID is NETGEAR.4. You will now see your wireless Security Option and passphrase. I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514
After fighting with this for the last couple of hours I have my ipod touch working with the netgear DG834G(v3) router. The fix is a bit odd and I am not entirely sure why it works but I thought I would share and hopefully it might help you out …
First I think that the WEP encryption simply does not work between these two devices and causes some very strange behaviour – the WEP 'authentication type' setting I had on the 'wireless settings' page was set to 'shared key' – I flicked this to 'automatic' & strength to ‘128 bit’ - hit apply and finally I found I was able to connect without an error message (after inputting the correct WEP key). Unfortunately the DHCP did not work correctly after this and I kept receiving IP addresses in the range of 169.254.x.x (an internal default) rather than my networks expected 192.168.0.x range.The Ipod touch couldn’t find any DNS servers or connect to the internet. To get round this I set the router ‘security options’ to use WPA instead (WPA-PSK (Wi-Fi Protected Access Pre-Shared Key)) instead of WEP. Set the new WPA password at the bottom of the wireless settings page - again hit apply - and configured the ipod to use the new password and WPA PSK instead of WEP.This worked fine – although it does mean I have to change the settings on all my other wireless devices around the house! The weird thing is that although the router isn’t using WEP encryption changing the 'authentication type' setting back to ‘shared key’ in the WEP menu breaks the WPA connection again – very odd? I blame netgear and their obviously crazy wep code :)
The router username is always admin The default password is password or (for older routers) 1234
Try the default username and password before resetting the router to the factory defaults.
When a router resets, it goes back to the state when it was new — all information that was entered by hand is lost! Examples are critical things you need to get online, such as ISP username, ISP password, IP addresses, security keys, and ports and services that were opened. It all needs to be re-entered.
So, have your ISP information before resetting the router.
Naturally, if you moved to a new city, or if you bought a used router, the old information in the router may not be of use to you. Contact your ISP if you can't connect any computer directly to the Internet. Then, if there is a connection problem when the router is added, see No Internet Access Through the Router
Reset for most routers with a reset button on the rear panel
Write down configuration information such as IP addresses, security keys, opened ports and services, etc., that you modified. (The default username is admin and the password is either password or 1234. Try these before resetting the router.)
Press the reset button on the back until the test light blinks.
This takes about 10 seconds.
(To avoid accidental resets, the small button is recessed. Use a pen or paperclip to access it.)
Release the button. Wait for the router to reboot.
Log in with the default password. If the router was not cleared, try these additional steps AFTER the router has finished rebooting.
Unplug the router's power. Press and hold the reset button.
While the button is held down, reconnect router's power. Continue to hold the reset button for 20 seconds after reconnecting the power.
Wait for the router to reboot. Log in with the default password
First thing to check here if the pc is getting a valid IP address to do this go to Command prompt and then type IPCONFIG and hit enter the computer should have a 192.x.x.x IP address if it does do this next step on the command prompt type this command PING YAHOO.COM and hit enter check if you will receive 4 replies after you hit enter if you receive Request timed out there a chance that a security software is blocking the connection like a firewall so disable that firewall for the mean time , but if you receive 4 replies it means that internet is really working on the computer and there's just something wrong with your Internet explorer of Firefox settings.. For internet explorer follow this, Click on Tools > Internet options > connections tab > Lan settings make sure nothing is check and also select never dial a connection then click OK and restart the computer.. Then after that try the internet if its working now....
old old post,
reset the router start over, all have reset button hold for 30second and release and it goes back to factory settings and no PW.
the manual covers that. here.
v1 is here, thy have 3 versions, not just one. of this device.
https://www.netgear.com/support/product/WN2000RPTv1.aspx
Do you have the range extender set up on the same live in the fuse box? If you have the one side on a breaker on the opposite side of the fuse box from the othrr side, it will not work well at all. That is why I encourage people not to waste their money on these things and get a decent wireless system so that you dont have problems.
the wireless B/G standards are not OS dependent.
are you able to go online with the Mac ?
are you able to download software or music with the PC ?
any messages on the Mac when downloading ?
go to negear.com
find your router, and read the manual..
RTM
what you want to do with no model stated router, is not know by us..
wifi, , Ethernet, and its firewall , or even VPNs are covered
hello, when you say after connecting to AOL 9.0 internet connection is lost, do you mean aol explorer doesn't work, or do you mean IE stops open pages and it was openning before starting AOL? if you close out your AOL does IE then starts working? or tell me what do you have to get it working again?