Panasonic AG - Popular Questions, Answers, Tips & Manuals - Page 5
Panasonic AG DVC30. ALMOST new..only
This being a new set and if under warranty you MUST not attempt to openor tamper so as to VOID the warranty.
Now the obserrvation of the fault seems to be linked to a problem in the main processing board.
the static noise indicates that the servo or the luminance.
The fault requires that you will need a proper signal trace, use of an oscilloscope for video signal and a use of a proper service manual and Jig for looking into the board when it is disembled.
hence my request for such a fault seems that it be checked with the service center, take estimate and decide.
Sometimes a fault connection, and inter board connector, loose grounding or a improper shield, or dry soldering in the linking cords/ boards can be the reason but will require a close look with a magnification glass.
9/14/2011 6:25:44 AM •
Panasonic...
•
42 views • 0 helpful votes
The model number of the
I had the same problem. Mine happened when the temperature was somewhat cooler than normal.
8/2/2011 9:08:36 AM •
Panasonic...
•
104 views • 0 helpful votes
My computer doesnt see my
Go to the panasonic website and see if they have any driver downloads for your model of camcorder. If they have download the driver and that may fix your problem
6/3/2011 12:32:55 PM •
Panasonic...
•
443 views • 1 helpful votes
Dead Pixel in Panasonic AG-DVC200
you can't do anything on dead pixel but still you can use the unit it will not affect any, else the dead pixel cover half of the screen.
5/23/2011 4:22:02 PM •
Panasonic...
•
265 views • 0 helpful votes
Auto off cylinder lock error
It seems that the cylinder head drum is not turning as there is a failure in the servo system , the servo motor or the drive.
This can also be due to failure of the HALL IC which switches the motor driver IC or it can be a failure of the power to the drive or even a mechanical block on the cylinder.
Open the cassette tray and feel the drum to be free, if so use a hair dryer to warm the inside of the set with the tray open so as to dispel any moisture which could have triggered the DEW switch to cut off the cylinder so as to prevent tape entangling.
If this wont work then there is fault in the servo which might need a qualified tech help.
3/11/2011 1:04:30 PM •
Panasonic...
•
1,455 views • 0 helpful votes
Buongiorno.la macchina in questione
ciao!per difetto di linea di panasonic ag dp800,ho avuto steso problemo,100% sono tre filtri di condensatore elektrolitici,nella scheda video 3700[c 03/c06/c09] e sicuro dopo sostituire tutto ok,o provato io alcuni giorni fa.piu meglio e per sostituire tutti condensatori delle schede video.piu info nell mio email[
[email protected]]
5/17/2011 2:10:00 PM •
Panasonic...
•
207 views • 2 helpful votes
My Panasonic DVC30 camcorder eats tapes on record
Tape mechanism problems can be quite complicated. This will require disassembling the camera to repair the tape mechanism and can be done fairly inexpensively. However, it's not a user serviceable problem and will need to be repaired by a qualified service technician.
My name is Rick and I'm a professional repair technician with over 20 years in the business and have repaired many of these. I'm semi retired and work from home with little overhead so I can keep repair costs low. If you decide to have the camera repaired, please click HERE for a directory listing that suits your needs.
If this response has been of any help to you, please be sure and give a positive vote for me on FixYa.com.
5/10/2011 6:47:47 PM •
Panasonic...
•
175 views • 0 helpful votes
Can you please advise what
At the theatre prior to the performance, ask the lighting director to show you one of the brighter performance stage light configurations and allow you to set the camera's white-balance. (It's easier to deal with a little under-exposure in post production, than it is for over-exposure.) Then adjust the exposure accordingly during the performance.
Preparation/Planning: Either at home or in the theatre, if you practice setting the white balance and then adjusting the exposure for varying levels of light, with your camera connected to a video monitor, so you will see it more clearly in real time, it will help adjustments during filming the performance more fluid.
Also consider using a lens filter. Practice various combinations to see what suits different light levels and gels for best effects. When possible, if using a stand alone camera (not cabled into a control room set-up) I prefer using a video monitor for each camera person to give better ability to manage adjustments of camera settings as needed.
5/16/2011 5:10:42 AM •
Panasonic...
•
125 views • 1 helpful votes
My HVX-200 power will not work. Camera will not
Hi,
I Hope the steps below should be helpful in fixing your camera issue.
Fixing a Lens Error on a Digital Camera
This has to be THE most common failure mode for a digital camera. Some
common error messages that might show up on the LCD's of cameras with
this problem include "E18 lens error", or "lens error, restart camera".
Some cameras might show nothing at all, but merely make a beeping noise
as the lens goes out, then in, then the camera shuts off. Sometimes the
lens won't even move.
The problem is actually quite common throughout all camera brands.
Usually it's sand or grit interfering with the lens extension mechanism.
Or the camera's been dropped with the lens extended. Or the camera has
been powered on, but the lens had been blocked preventing its extension.
Or the battery ran down with the lens extended. Believe it or not, one
BIG contributor to lens errors is using a camera case. Sand, gunk, case
fibers, etc... accumulate at the bottom of the case. These materials
love to cling to the camera by electrostatic build-up from the camera
rubbing against the side of the case (especially those cases with soft
fibrous intreriors). Once these materials work their way into the lens
mechanism, that's all she wrote. I have many Canon's, and NEVER use a
case for this very reason.
A camera owner that suffers this problem may have no recourse for having
the camera repaired. Many camera makers will not honor repairing this
problem under warranty as they claim it is due to impact damage to the
camera, or sand or debris getting into the lens gearing mechanism
(neither of which is covered under warranty). The quoted repair cost is
usually close to or more than what the camera is actually worth.
Fortunately, about half the cameras that suffer this failure can easily
be fixed by one of the following methods. None of these methods involve
opening the camera, although some have potential to cause other damage
to the camera if excessively done. If the camera is still under
warranty, before trying any of these, please please first contact your
camera's maker to see if they'll cover the repair, or to determine how
much they'll charge for the repair. Who knows, you might get lucky. But
if they quote you a number that's higher than the value of your camera,
you may want to consider the following methods.
The methods are listed in the order of risk of damaging your camera.
Thus make sure you try them in the listed order. And remember, these
fixes (especially #6 and 7) should only be considered for a camera
that's out of warranty, who's cost of repair would be excessive, and
would otherwise be considered for disposal if unrepaired:
Fix #1: Remove the batteries from the camera, wait a few minutes.
Put a fresh set of batteries back in (preferably rechargeable NiMH
2500mah or better) and turn the camera on. If that didn't work, try
pressing and holding the Function or OK button while turning the camera
on.
Fix #2: Remove the batteries, then remove the memory card. Then
install new batteries, and turn on the camera. If you get an Error E30,
it means you don't have a memory card installed, so turn it off, slip in
the memory card and turn it on one last time.
Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the
camera on. Inserting this cable ensures that the camera's LCD screen
remains off during the start process. Thus extra battery power is
available to the camera's lens motor during startup. This extra power
can be useful in overcoming grit or sand particals that may be jamming
the lens. If the AV cable doesn't fix the lens error by itself, consider
keeping this cable installed while trying fixes 4, 5, and 7 as a means
to provide extra help to these fixes. But note that I DON'T recommend
keeping the cable installed during Fix 6 as you may damage the AV port
while tapping the camera. Reinsert the cable only AFTER tapping the
camera.
Fix #4: Place the camera flat on its back on a table, pointed at
the ceiling. Press and hold the shutter button down, and at the same
time press the power-on button. The idea is that the camera will try to
autofocus while the lens is extending, hopefully seating the lens barrel
guide pins in their slots.
Fix #5: Blow compressed air in the gaps around the lens barrels
with the idea of blowing out any sand or grit that may be in there
jamming the lens. Other variations include blowing with a hair dryer in
"no heat" setting, or sucking the gaps with a vacuum (careful with this
one).
Now we're entering into the realm of potentially damaging your
camera in conducting the fix. There is definitely some risk here, so
take care when conducting the following two fixes.
Fix #6: Repeatedly tap the padded/rubber usb cover on a hard
surface with the intent of dislodging any particles that may be jamming
the lens. Other variations include hitting a side of the camera against
the palm of your hand. A lot of people have reported success with this
method. HOWEVER, there is also some potential for damaging or dislodging
internal components with this method, such as unseating ribbon cables,
or cracking LCD screens.
Fix #7: Try forcing the lens. More people have reported success
with this method than with any of the other methods. HOWEVER, there's
obviously some potential for damaging your camera by using this method.
Variations include gently pulling, rotating, and/or twisting the lens
barrel while hitting the power button. Attempt to gently straighten or
align the barrel if it's crooked or twisted. Another variation includes
looking for uneven gaps around the lens barrel, and then pushing on the
side of the lens barrel that has the largest gap (note pushing the lens
barrel all the way in is NOT recommended as it may become stuck there).
While doing any of the above, listen for a click that indicates that the
lens barrel guide pins may have reseated in their guide slots. If you
hear this click, immediately stop and try the camera.
Regards,
Ron
* Please rate this solution with Thumbs up and Testimony to help us improve providing support
2/23/2011 7:35:15 PM •
Panasonic...
•
596 views • 0 helpful votes
I have a Panasonic
On the cassette shell is a small sliding door that prevents recording, move it to the record position.
The idea is to protect a valuable tape from being recorded over.
3/27/2011 5:51:07 PM •
Panasonic...
•
194 views • 1 helpful votes
Hi all, I run the panasonic camcorder ag-dvx100b
I have looked at the video.There doesn't appear to be anything wrong with the camcorder.The problem is more from the angle at which you are recording.You seem to be a little offset from center,probably because there are seats in the center and you do not want or cannot record from there so that people may sit in the middle or behind that without an obstructed view.Are you recording from as close to the seats as possible,meaning in the aisle?Try recording from the center,even if it's in a seating area.You should try experimenting a little.Have someone stand towards the center,like in the video.Move your camera around to different areas and see where you can get the best results from.Move to the furthest area back,and see how close you can zoom in to get a good picture.Then work inwards from there.If you do not have a full capacity crowd,they will understand even if you are in the seating area taking video.It should not block a whole lot of seat views.If you are quite full,just move farther back.TAKE NOTES when you are attempting to get a good picture.Seat,row,location,etc.Then you have a quick reference to adjust to if necessary.Even if all 3 legs of the tripod are not able to extend fully if shooting from a seat row,the 3rd leg should be able to shorten up to put on the seat,but you may have to weight the seat down if they are the ones which automatically pop up.If the seats have a gap between the back of the seat and the upright part,you will probably have to rig something to hold the leg in place.Using the tripod in the seat,the best idea would be to push the 3rd leg which is on the seat up against the back edge and wedge it there somehow.That would give you the best stability. gmccarthy 86 hotmail If you reply,please write something in subj line so I know it's a good email because it will show up in my junk at first.Also,a note for the speaker.When listening to public speaking,'filler' words like uh and um are VERY annoying to many who are listening.Have the speaker look at himself on video and practice not doing this.He is doing it quite a bit.Personally,that alone would have gotten me to walk out after a short time if I were at this particular link's sermon. Good luck,Greg
2/24/2011 3:48:33 PM •
Panasonic...
•
155 views • 0 helpful votes
Hi ~ just purchased a
Almost all the time rattling inside a camera is bad, i suggest returning it or contacting panasonic
3/17/2011 10:40:21 PM •
Panasonic...
•
88 views • 0 helpful votes
Have a ag-dvx100bp How do
Hi,
To transfer the videos from the Camcorder to the Computer, I suggest you to use the IEEE 1394 cable (4-pin) (i.LINK, Firewire). You can connect the 4 pin DV cable from the Camcorder to the DV IN port on the Computer.
You require to purchase either a 4 - pin to 4 - pin or a 4 - pin to 6 - pin i.LINK / Firewire cable depending on the number of pins on the i.LINK / Firewire port of your computer (since Camcorder will have only 4PIN i-LINK, while the Computer may have a 4PIN or 6 PIN i.LINK port).
i.LINK is the same as Firewire/IEEE1394. It is a D Shaped connector of either 4 or 6 pins. The type of cable to be used will depend on the i.LINK port of your computer.
If your computer does not feature this port, you may contact your Computer retailer to install a separate i.LINK Capture card in your computer. The software and driver to be used for video transfer will be supplied by the computer manufacturer (if the computer came with an i.LINK interface) or else by the i.LINK card manufacturer.
To transfer the video using the DV interface, you need to set the Power switch to VCR mode and you can use the Windows Movie Maker Software to transfer the videos.
Thanks for using FixYa.
2/25/2011 5:47:47 AM •
Panasonic...
•
124 views • 1 helpful votes
Not finding what you are looking for?