Panasonic Office Equipment & Supplies - Page 4 - Recent Questions, Troubleshooting & Support

Hi. Panasonic Workio DP-1820P error code E02-01 These instructions describe error code E02-01 solution for a Panasonic Workio DP-1520p, DP-1820P copier machine. This should solve your problem; this introduction will help you to troubleshoot some common error messages related to Panasonic Workio DP-1520p, DP-1820P Error Code E2-01, E2-02, E2-03, and E2-04 that you may receive.

Meaning of E02-01 the Error Code:

E02-01 means the Tray 1 cassette lifting motor unit fault. These machines use a lift motor encased in a plastic drive gear casing. Usually something inside the casing breaks, this usually happens in trays that have Ledger or Legal paper installed. The weight of the paper can cause these gear packs to break. Also if the customer loads letter paper in a tray set up for larger paper sizes.

How to fix the error:

Maybe a problem with tray 1 lift motor either you have a bad motor, Pull the paper tray out and see if the paper is lodged behind the tray, Also make sure the white coupling on the rear wall is in one piece. Check that the flag on the back of the tray is still present. Mostly it is broken and sometimes can be repaired, and otherwise, you have to change it, and to open the back cover and reach that (Part no is (DZTY000357 Paper Lift Motor Assembly, lift up drive).

Some of the possible causes:

• Remove the tray and check for paper behind the tray.
• Check paper falls back causing the gears to break.
• Check cassette Lift Motor connector.
• Replace the Tray 1 lift motor.
• Check the Mainboard.

Good luck.

What Does Call Service 2 Means On Panasonic KX-MB2030?

If none of functions are we working and there is power to the unit, there is no simple solution to a fix.

However, you could try disconnecting the problems with Panasonic service. You can contact them here:

https://www.justanswer.com/sip/panasonic-help-24-7?r=ppc|ga|6|Tech%20-%20Computer%20-%20Top%20Brands%20-%20Search|Panasonic%20Computers%20-%20Broad&JPKW=panasonic%20problem&JPDC=S&JPST=&JPAD=315133615174&JPMT=b&JPNW=g&JPAF=txt&JPCD=20181127&JPRC=1&JPOP=TM-Top1k-Set5&r=ppc|ga|6|||&JPKW=panasonic%20problem&JPDC=S&JPST=&JPAD=315133615174&JPMT=b&JPNW=g&JPAF=txt&JPRC=1&JPCD=&JPOP=&cmpid=37426822&agid=1329344242&fiid=&tgtid=kwd-2544329325&ntw=g&dvc=m&gclid=CjwKCAjwsMzzBRACEiwAx4lLGxH2wU5EX35eby4COZcJBNO7eqAcTBd2wx2zU45CKRKfcwT6wUa2HxoC34UQAvD_BwE

do you have it hooked up through wifi

https://printcopy.info/index.php?mod=erc&brand=Konica-Minolta&model=bizhub%20500&code=C-6001 https://www.scribd.com/doc/36290558/Minolta-EP8015-EP6001-SERVICE-MANUAL

In the manual it will tell you how to reset the drum counter on Page 190 (DP-C265 manual). Reset all the different counters and that will likely clear the problem. A lot of sites want you to buy new drums at $170 a crack. I have reset mine 3 times already and still have perfect printing over 100,000 copies later.

Do it

What i have seen is the big white gear behind the flywheel is broken where the gear mates with the pin on the shaft.

you need to have the latest scanning software "" www.workio.com "" and you need the name and key name inserted in the software

Press Menu first, then #9000*, next press 550, press Start, wait for printing, unplug the electric cord, wait 10s or more, plug it again, it's done.

MADISON, Your message does not qualify as a question or query for a problem, try somewhere else DO NOT MAKE THIS SITE WITH YOUR GARBAGE Take your GARBAGE to another Side Your message qualifies as SPAM

Your message does not qualify as a question or query for a problem, try somewhere else DO NOT MAKE THIS SITE WITH YOUR GARBAGE Take your GARBAGE to another Side Your message qualifies as SPAM

Try this utube link. I did it and it solved the problem in about 30 seconds! Don't spend any money or send out your unit. This does it.

http://www.youtube.com/watch?v=6jGwB05_gdk

Su mensaje no califica como una pregunta o consulta para un problema, intente en otro lugar NO HAGA ESTE SITIO CON SU BASURA Lleve su BASURA a otro lado Su mensaje califica como SPAM

You have a bad LASER unit.

means that the machine needs a good cleaning because it reached so many copies. has to be serviced by a dealer

"E1-22" 5th & 6th mirror assy. sensor problemMirrors are out of position, was someone cleaning the mirrors or touched for it for a reason??? if not the sensors are bad

Description

Corona Wire cleaning

Causes

1. Cleaner Home Position Sensor 1 connector is disconnected. 2. Cleaner Home Position Sensor 1 is defective. 3. Cleaner Home Position Sensor 2 connector is disconnected. 4. Cleaner Home Position Sensor 2 is defective. 5. Cleaner Motor Drive Mechanism is defective. 6. Corona Mechanism is defective. 7. Cleaner Motor connector is disconnected. 8. Cleaner Motor is defective. 9. DRV PCB connector is disconnected. 10. DRV PCB is defective. 11. SPC PCB connector is disconnected. 12. SPC PCB is defective. 13. LVPS is defective.

Drum Motor rotation Causes1. Drum Drive Mechanism is defective check drum drive system