Panasonic Answered Questions & Fixed Issues

Normally spots. A black line suggests a scratched CCD Sensor.https://www.google.com/search?q=Panasonic+Lumix+DMC-TZ30+black+line+in+camera+lens..

ok va bene

All question need full 'make model (what it is)' please Use Search in the manual (CTRL+F) https://www.partmaster.co.uk/images/mediator/121/service%20manual%20-%20nr-b29sg2-sb%20,%20nr-b29sw2-wb%20%26%20nr-b32sg2-sb.pdf More here https://www.google.com/search?q=Panasonic+inverter+fridge+showing+Sr+and+E ..

1. Check the Power Cord: Ensure that the power cord is securely plugged into both the TV and the power outlet. Make sure there are no visible signs of damage to the power cord or the plug.
2. Inspect the Power Outlet: Try plugging another electronic device (such as a lamp or a phone charger) into the same outlet to verify if it is functioning properly. If other devices work fine, then the issue is likely not with the power outlet.
3. Check for Tripped Circuit Breakers: Check your circuit breaker or fuse box to see if a circuit breaker has been tripped or a fuse blown. If so, reset the circuit breaker or replace the fuse and try plugging in your TV again.
4. Test with Different Power Source: If possible, try plugging your TV into a different power source altogether, such as a different room or building. This will help determine if the issue is specific to the power source you were previously using.
5. Contact Panasonic Support: If none of the above steps resolve the issue and your TV still does not power on, it's likely that there is a hardware problem with the TV itself. In this case, you may need to contact Panasonic customer support for further assistance or to arrange for repairs. Be sure to provide them with details of the troubleshooting steps you've already taken.

Hope this helps

1. Check the Input Source: Make sure you have selected the correct input source on your TV for the device you are using. Use the remote control to cycle through the input options until you find the one connected to your video source.
2. Check Video Connections: Ensure that all video cables (such as HDMI, component, or composite cables) are securely connected between your TV and the device you are trying to watch content from. A loose or faulty cable connection could result in a loss of video signal.
3. Restart the TV and Video Source: Try restarting both your TV and the device you are trying to watch content from. Power off both devices, wait a few moments, and then power them back on. This can sometimes resolve temporary glitches or issues with the video signal.
4. Check for Software Updates: Make sure your TV's firmware is up-to-date. Sometimes software updates can resolve compatibility issues or bugs that may be affecting video playback. Check the settings menu on your TV for an option to update the firmware, or visit the manufacturer's website for instructions on how to do so.
5. Reset Video Settings: If you've made any changes to your TV's video settings, such as resolution or picture mode, try resetting them to their default values. This can sometimes resolve issues with video playback.
6. Try a Different Device: If possible, try connecting a different device (such as a DVD player or gaming console) to your TV to see if the issue persists. This can help determine whether the problem lies with the TV itself or with the original device you were using.
7. Contact Panasonic Support: If none of the above steps resolve the issue, it's possible there may be a hardware problem with your TV. In this case, you may need to contact Panasonic customer support for further assistance or to schedule a repair.
8. Hope this helps

Try the Power Reset procedure. https://www.google.com/search?q=Panasonic+FZ-55+tough+book+not+shutting+down ..

The nearest you will get is the service manual. Dowmload the service manual and follow the dissasambly and reassambly instructions to the letter, otherwise it will not work correctly and the timing will be out. https://elektrotanya.com/panasonic_sa-ak20.pdf/download.html

Question edited for clarity. Question moved from Televisions https://www.google.com/search?q=Panasonic+NN9853+control+panel+schematic https://www.google.com/search?q=panasonic+nn+9853+service+manual+pdf https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

Most probably the low voltage transformer of in the control panel is open . It has a thermal fuse which is between pin1 and pin 5 of the low voltage transformer. This fuse is however inside the transformer. If you get a DC resistance of about 350- 400 ohms between pin 5 and 6 of the transormer , connect an external 500ma fuse between pin 1 and pin5

Question edited for a lot more clarity. In the link https://www.google.com/search?q=panasonic+th-42pv8d+blinks+2+times ..

Unplug all the extensions and then plug them back in one at a time. https://www.google.com/search?q=Panasonic+KX-T7730+unable+to+call+another+extension ..

i would check the user manual if it were me. Here´s the an excerpt from the manual. * For more detail on usage of 3D Eyewear (Power button and Accessories etc.), please refer to operating manuals for the purchased 3D Eyewear seeing it differs depending on the type of 3D Eyewear (Model No. of 3D Eyewear). Wearing the 3D Eyewear Turn on the 3D Eyewear Put on the 3D Eyewear View When the HDMI receives information in which 3D mode is detected, 3D images are automatically displayed according to the signal. If the 3D images are not displayed correctly or the images cause discomfort, the images can be adjusted by "3D format select" or "3D settings". ? Change the view 3D?2D, 3D settings (p.25) After Use Turn off the 3D Eyewear. After using the 3D Eyewear, store it in the case provided.

panasonic sa-vk-31-gc-sm - service manual

Elektrotanya https://elektrotanya.com > download ·Translate this page Download PANASONIC SA-VK-31-GC-SM service manual & repair info for electronics experts. ..

Question edited for clarity. Loose connections. Dry joint on a board. Failing capacitors. Overheating. https://www.google.com/search?q=Panasonic+Strada+CN-E205D+turning+on+and+off ..

How to change the language to English on a Panasonic strada cn-h500wd

Unfortunately there isn't one. The workaround is to change the Router Password or SSID to remove the plus + for something else.

need to input the plus sign for wifipassword XXXXX my ...

JustAnswer https://www.justanswer.com > Network Experts Apr 6, 2014 - How do i type the plus sign for my wifi password on my panasonic viera remote? I also need to input the "+" sign. - Answered by a verified 1 answer · Top answer: Okay, great. Go to Network settings on your tv menu> select Wireless ne https://www.google.com/search?q=Panasonic+remote+plus+symbol ..

panasonic tc-2165ga

Try disconnecting all of the speakers except the left and right main speakers. If it works, check the wiring at the back of each speaker to make sure there aren't any shorts between the terminals. Better yet, just inspect the terminals both at the audio unit and the backs of the speakers. Stray strands of wire reaching across to the other terminal or exposed wire on the other side are a common problem. If you have that all cleaned up and still have the error, you may have shorted transistors in the output amp of one of the channels, very likely the subwoofer. This may be caused by shorted speaker wiring, or the amp may have failed on its own. In either case, you would have to replace both of the output transistors for that channel (they may be built into a power amp module, in which case the module must be replaced). This requires soldering skill, and the knowledge to identify the transistors and check them with an ohmmeter. Most of the time, it's a basic job for any skilled electronic technician. (I did run into one model that would have required two days of disassembly labor just to get at the failed transistors - I told the customer that wasn't designed for service and he would be better off buying something different to replace it.)

I had a blinking green light on the charger when I would put the battery on the charger. I noticed some black buildup on the prongs of the battery and scrapped it off and now the battery charger is displaying solid green. It may end up being a quick fix considering my equipment came from ebay and already had some light wear and tear