Proscan Tablets & eReaders - Recent Questions, Troubleshooting & Support


There should be a rest set system button , you may have to use a small paper clip unfolded to fit into the area. But that should do it. Good luck

Proscan 7-Inch... | Answered on May 07, 2019


Do a factory reset this will remove any passwords, however it will also wipe all data pictures and so on.

Proscan 7-Inch... | Answered on Apr 29, 2019


tell him to make "that face again" Sorry? I couldn't resist

Proscan 7-Inch... | Answered on Apr 26, 2019


Do a hard reset, press and hold the +vol button, then the power button, wait about 20 seconds both buttons held till the start android screen appears. Hope that helps

Proscan 7-Inch... | Answered on Apr 19, 2019


It would be cheaper to buy a new tablet than to replace the cracked screen. The damage could be further than just the screen. This could make it not unlock.

Proscan 7-Inch... | Answered on Apr 17, 2019


contact wherever you bought it,it will be warranteed as long as you used the proper charger and unplugged it when done charging,but,it sounds to me that you might of used the wrong charger

Proscan 7-Inch... | Answered on Mar 06, 2019


Screen or outside measurements? Strange question. Why not just get a ruler?

Proscan 7-Inch... | Answered on Dec 20, 2018


This tablet is absolutely junk.
Just throw it in the trash can.(don't forget to reset it to wipe everything off) And please don't give it to anyone, you might be sued....Haha.... Paul H

Proscan... | Answered on Oct 30, 2018


sorry Fixya DID NOT SELL YOU ANYTHING

Proscan Tablets... | Answered on Dec 24, 2017


Not being able to update any apps simply means either you don't have access to the internet or that your apps update is programmed to function ONLY when you are connected to/through WiFi.

second, you can download standalone 'raw' apk files online and install on your tab.

Remember to go into your Settings---Security (and under Device administration, check 'Unknown sources' and activate 'allow installation of apps from unknown sources'.
Done.

This is safe.

Post update or feedback please

Proscan 8 4GB... | Answered on Oct 11, 2017


try holding power button and vol up at same time until screen comes on

Proscan... | Answered on Apr 18, 2017


I have had the same issue with this tablet. After weeks of looking around on the net i have found a way to reset the tablet to factory settings when the power and vol down button will not work.

1. Download the firmware from the proscan website. http://www.proscanvideo.com/item.asp?itemnmbr=PLT8235G.

2. unzip the file and copy the files update.zip recovery.img and factory_update_param.aml to an external micro sd card.

3. Plug the tablet in and insert the sd card. Press the power button to see the battery icon then press the power button 5 times. Then let it run for 4 minutes and it should be set back to factory settings.

****NOTE***** If it fails to update then you still have the access to the recovery menu where you can do the factory wipe and still reset it.

Hope this helps.

Proscan 8 4GB... | Answered on Feb 15, 2017


Someone inputted a security code at some point, no other explanation, of course you are now stuck, you will need to perform a factory reset to overcome this problem.

Proscan 7-Inch... | Answered on Oct 28, 2016

Not finding what you are looking for?
Proscan Logo

356 questions posted

Ask a Question

Usually answered in minutes!

Top Proscan Tablets & eReaders Experts

 Mike M
Mike M

Level 3 Expert

3324 Answers

Pollo

Level 1 Expert

11 Answers

Ngoro

Level 3 Expert

1903 Answers

Are you a Proscan Tablet and eReader Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...