Proscan Televison & Video - Page 2 - Recent Questions, Troubleshooting & Support
Who makes proscan tv?
Proscan is produced by ON Corp. They are a leading producer for most LCD screens used by a large group of TV makers. Proscan used to be a high end RCA product. The CEO of On Corp was the head of the Proscan division of RCA. After Leaving RCA and Beginning On Corp he purchased the right to the Proscan trade mark. Thus a new beginning for a old name. Many people still belive it to be an RCA TV but it is not. It has good ratings in most reviews for TV's in it price range. It is now a sears brand much like Dynex is a Best But brand.
Pixel gone
No this is whats called a dead pixel. Since it's white the transistor at that pixel area is shorted. Depending on the age of the unit the manufactor may replace the unit if not the whole panel will have to be replaced at a cost of more than the unit cost. Most manufactor says more then one pixel has to be bad before they will do anything.
No picture but sound on my proscan
Check its speaker first. If it is OK, check and replace damaged component/s at its audio amplifier section circuit. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
https://elektrotricks.blogspot.com/
faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent. Search the site by type in the brand name and model of your set, in its search bar at the right side column, and press enter.
3/3/2021 2:57:10 PM •
Proscan...
•
Answered
on Mar 03, 2021
Problem with Proscan PLCD5092A-B
I replaced the main board with no luck :
Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.
11/24/2020 8:24:28 PM •
Proscan...
•
Answered
on Nov 24, 2020
Dvd player wont play
I found this on the PROSCAN website under customer support manuals.The website is www.oncorpus.com.I hope this information helps you with your problem. IMPORTANT THE LABEL SIDE OF THE DVD MUST FACE THE BACK SIDE OF THE TELEVISION 1. Press the ‘INPUT’ button to select ‘DVD’ mode, if no disc is inserted yet, the display shows ‘No Disc’.
2.Insert a DVD with the printed side facing towards the rear of the TV/DVD Player (see below)
3.The TV will first display ‘Loading’, then change to ‘DVD-video’. Most DVDs will show some preliminary
information then stop at a main menu screen.
4. Press PLAY/PAUSE to play it directly. Or press the DVD-MENU button to access the disc menu during
playback.
5.Use the direction button on the remote control to select the desired option. Press ENTER to select the
option or press the ► button. Playback will now commence.
6.After playback, press the EJECT button on remote control or EJECT button on TV/DVD to remove the
disc.
Note: No function‘’ will sometimes appear on the screen after a button is pressed. This indicates that the
function is not supported at the current time.
Not finding what you are looking for?