Samsung LN - Answered Questions & Fixed Issues - Page 5
BN97-02472C issue
It doesn't seem to
Hi,
Unfortunately capacitors have been projected as a cure to all possible problems in an LCD tv by some you tube experts. The actual problem may lie in the power board or the main board. An expert is needed to check and find the actual culprit.
How to connect my bose solo to my 2009 samsung tv
sounds like you have it set correctly..do you have any other sources than external,(such as audio out) ?If so that should solve your problem...does the system have any other connection outs, such as red white audio cables (LR audio )? You can use them as external when the optical is unplugged...if you get sound you either have a bad optical cord or the output for it is defective..good luck GOD BLESS
Samsung LN-T4042H will not recognize blu ray player
The issue is with the main board circuits on your set not detecting signal on HDMI ports or selecting those ports.
How about your other inputs - do they work? Have a feeling they also will be dead. If course you can always feed the dvd rf signal to your set but the audio and video will not be up to current standards but it will work like that.
9/21/2017 4:21:53 PM •
Samsung...
•
Answered
on Sep 21, 2017
•
118 views
I have a Samsung LN-s2651d LCD tv that black
Do flashlight test on unit. If you can see an image thruout screen the problem is with the tcon board. If no image then it is the inverter board/circuits.
9/12/2017 3:11:37 PM •
Samsung...
•
Answered
on Sep 12, 2017
•
191 views
Black screen
Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electronicshelponline.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main digital board.
I have a Samsung LN-T3253H
Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.
9/3/2017 1:09:25 PM •
Samsung...
•
Answered
on Sep 03, 2017
•
161 views
Connect hdmi goodmans tv
Forgive on this one but I do not have a soundbar but wonder if it has any other connections like phono for input as to me hdmi would be a strange choice. Hdmi leads are mostly alike in they are fully wired and carry a wire which directs a device to listen to it when turned on, also some hdmi sockets (like the old scart) are blessed with options.
Some may be input only while others set for in and out so it may be worth swapping connections on your TV to see if this changes the habit, though for me I would look to see if this soundbar has other sockets to use like phono (same with your TV if it has phono or scart socket options). Your TV instructions may show their ideal connection setup, otherwise you will have to shutdown your other item to stop it commanding the TV to switch through its sound. This "problem" is an old one with people using scart leads then I used to cut pin 8 (its control wire handing the descision to a user) but this new lead combo I do not know.
Hope this helps.........
Image on menu good but upside and image on cable bad and uspide and after a minute or two tv turn off and on repetivly LN22A450
Sounds like age has caught up with it and may have component failure which for an item that age is not worth it, your only possible chance may be to factory reset it back to its original state this feature should be found in its install/menu settings this will wipe all settings made in its life. Then you will need to reset every thing but hope the problem has cleared in this process.
If not then a new one is needed, as repair would be costly and I doubt worth it in the long run.
Hope this helps..........
STUCK IN STANDBY
Fault at its main digital board.
Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.
TV turns on, then goes "black"
85% of the time it will be a capacitor ! look at the top of them and if they have a bulge or have been leaking thats the problem there is many of them so study them hard
8/7/2017 10:15:01 AM •
Samsung...
•
Answered
on Aug 07, 2017
•
298 views
CHANGING THE CAPACITORS DID NOT
Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electro-medical.blogspot.com/
http://homenol.blogspot.com/
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "
brand name" to your device,
[Exclude the model number] in the "
Search box at the top right of the display window of the Homepage" to get gathered related posts.
7/18/2017 1:38:18 PM •
Samsung...
•
Answered
on Jul 18, 2017
•
95 views
Not finding what you are looking for?