Splendide Washing Machines - Page 5 - Answered Questions & Fixed Issues

PUREX makes a sheet that contains detergent and softener. I cut them in half to use in the RV. It is perfect for a combo.

MAKE SURE YOU CAN COLLECT THE WATER AND WILL NOT DAMAGE ANYTHING BEFORE YOU DO THE FOLLOWING! In the front bottom right, is a water plug. unscrew it. water will drain. check if debis in there and look at impeller. The reason why the dial spins, is because it is giving you a fault code. count the number of the red light blinks. i have the diagnostic manual that has the fault codes that shows how to check components with an OHM meter

it is a fault code. fault code 12 is a communication problem with module board. check to see if any lose wires. i have the diagnostic manual. in it, it shows what OHMS are at each wire. I can share the pdf manual on face book. look me up GARY LEE TAMPA FLORIDA and add me as friend w/ a note you want the SPLENDIDE DIAGNOSES MANUAL

remove blower motor and remove caked on lent and check the over heat safety breakers with an ohm meter. also\, i find it dry faster in high speed spin mode. hope this helps

www.splendide.com
1-800-356-0766 #5 (503-656-2280)
503-722-9202
[email protected]
Monday-Friday, 7:00am - 4:30pm (PST)

Either of these could tell you about your specific unit.

to do what you are saying is to remove controler and by pass every thing with individual switches would work in a fashion but is not feasable best dump it now or repair propely for safety reasons remember a life is worth more than any money when playing with electric and water repair or get new dont take chances a family menber is is loved and would be missed

Just finished fixing mine. Found a broken wire at one of the high temp limits. Found tech service manual at Splendide,.com/service/TECHMANXC. It's a pdf file that will walk you through any repair.

It is so common that the washing machine can maketerrible noise in many ways and is a common fault. In all occasions it isimportant that your observation is most important and so is vital to theidentification /rectification and solution. If you have noticed that machine isvibrating when it is running then the motor /drum suspension has to beinspected. Since these fittings are located on the underside of the machine itis important that you look for the noise with a good inspection lamp. Manuallyturn the motor and drum and listen for the noise, if so the motor bearings, thedrum agitator shaft and fittings must be checked. Also the suspensions whichinclude the shock absorbers and springs, the body clamps must be checked to bein correct alignment and not changed in position. Tightening of themounting is also very important. Finallyin most cases a drop of OIL or smear of grease on the moving parts cane solvemost issues.Check this link :http://www.espares.co.uk/advice/washing-machines/a/7/1210/wobbly-washing-machine-or-tumble-dryer.htmlFor replacement of bearings check for tips on thisvisual link: http://www.espares.co.uk/advice/washing-machines/a/7/1401/how-to-replace-the-bearings-on-a-washing-mach.html

Possible that the door lock is jammed and needs to be replaced.please check this link;Replacing door lock

It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Check this link to replace the inlet valve:

http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the dry spin with the drain valve/pump activated so as to drain off all the water from the clothes during the spin.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.repairclinic.com/Washing-Machine-Troubleshooting?red=Washing-Machine-Repair-Help

www.RepairClinic.comSounds like the heating element quit.

I don't know if this will help or not I cannot find your exact model. Here is a link to a manual that Splendide makes maybe they are somewhat the same. Try Splendide.com site or this link: http://www.splendide.com/manual_wd2100_2000s.pdf

Maybe you can look through this link and see how it all goes together:http://www.beamalarm.com/foretravel-links/PDF/Splendide_Combo_Parts_Break_Down.pdf

Try the link I posted at the bottom. There is a phone # on page 1 and parts breakdown on pages 4-19http://www.beamalarm.com/foretravel-links/PDF/Splendide_Combo_Parts_Break_Down.pdf

Try this link at the bottom of my posting. There is a phone # on page 1 and parts shown on pages 4-19. It should be easy to replace, look it over take pictures as you go and if you can't remember how something goes together you can always look at the pictures.http://www.beamalarm.com/foretravel-links/PDF/Splendide_Combo_Parts_Break_Down.pdf

Here is a link to a parts PDF file, you should be able to look at the diagram and figure out where its supposed to attach to.http://www.beamalarm.com/foretravel-links/PDF/Splendide_Combo_Parts_Break_Down.pdf

Try looking at the link at the bottom. There is a phone # on page 1 and the parts for your machine is on pages 4-19. I hope this helps. http://www.beamalarm.com/foretravel-links/PDF/Splendide_Combo_Parts_Break_Down.pdf

Maybe fan is not working properly, or restricted vent in the first place, causing it not to flow properly and lint gets hung up. Is vent hose fairly straight or does it go around a lot of curves?

I attached a PDF link of the washer parts. On the front page (page 1) there is a phone # where you can talk to a technicion. Your washer is shown on pages 4-19. I hope this helps, click on or copy and paste this link into your browser: http://www.beamalarm.com/foretravel-links/PDF/Splendide_Combo_Parts_Break_Down.pdf

Is motor running? Maybe a broken belt? If motor does not run at all maybe door switch is not working.