If you do not have a remote for your Toshiba TV, there are a few ways you can access the menu to change settings or perform other functions:
Use the buttons on the TV: Some Toshiba TVs have buttons on the side or back of the TV that can be used to access the menu or perform other functions. Check the TV's manual or the label on the back of the TV to see if this is the case for your TV and which buttons to use.
Use a universal remote: You can purchase a universal remote that is compatible with your Toshiba TV. These remotes can be programmed to control your TV, and can be used to access the menu and other functions.
Connect a keyboard or mouse to the TV: If your TV has a USB port, you can connect a keyboard or mouse to the TV and use it to navigate the menu and other functions.
Use a mobile app: Some Toshiba TVs can be controlled using a mobile app that can be downloaded to your smartphone or tablet. This app allows you to control your TV and access the menu without needing a remote.
There could be an issue here with both the power supply and also an internal problem as well with your TV. The outlet that your TV is plugged into could be the issue here then.
Error code 0008 on a Toshiba 307 photocopier typically indicates a problem with the fusing unit. This could be caused by a malfunctioning thermistor or a problem with the fusing lamp. It is recommended to check the fusing unit and replace any faulty parts. If the problem persists, it may be necessary to call for service from a qualified technician.
There could be something wrong with your TVs power supply and an issue with the power board or the cables and the input devices might not be working and need to be replaced.
it sounds like the issue may be with the AV MAIN board. The power board is providing the correct voltage to the board, but the board itself may be malfunctioning. It may be necessary to replace the AV MAIN board in order to resolve the issue with the TV not producing video or sound. It is also possible that the problem could be elsewhere, but the AV MAIN board would be a good place to start troubleshooting.
1. Click "Start | All Programs | TOSHIBA | Utilities | HWSetup" to open the laptop's original equipment manufacturer, or OEM, system configuration software.
2. Click "General," then "Default" to reset the BIOS settings to their original state.
3. Click "Apply," then "OK."
Restore BIOS Settings at Startup 1. Restart or power on the Toshiba. Quickly press "F2" to access the boot screen. If you miss the boot screen and the computer continues to start Windows, shut down and try again.
2. Press "F9" to load the BIOS setup defaults on the laptop. Use the directional pad to select "Yes" and then press "Enter."
3. Go to the "Exit" tab. Select "Exit Saving Changes." Choose "Yes." Press "Enter" to quit.
You can download the device drivers for your model laptop from the Toshiba WEB site from their download page. Make sure you enter the model of your laptop so you can get the correct drivers. Please click on this link: - http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/home.jsp
The location of the IR sensor on a Toshiba Regza TV can vary depending on the specific model of the TV. However, in general, the IR sensor can be found in one of the following places:
On the front of the TV: The IR sensor is often located on the front of the TV, usually near the bottom or the top of the TV.
On the side of the TV: The IR sensor may be located on the left or right side of the TV.
On the back of the TV: The IR sensor can also be located on the back of the TV, usually near the bottom or the top of the TV.
On the remote control: The IR sensor can also be located on the remote control.
To locate the IR sensor, look for a small, clear or black plastic window that receives the signals from your remote control, it could be labeled with a name like "IR" or "remote".
It is recommended to consult the TV's user manual or contact Toshiba customer service for more specific information on the location of the IR sensor on your specific model of the Regza TV.
c380 indicates auto-toner error for black developer (K).
Check following:
Is the harness between the LGC board and the developer unit drawer connector open-circuited? Is any harness inside the developer unit or the auto-toner sensor harness open-circuited? Is the auto-toner sensor connector or the connector CN341 on the LGC board disconnected?
IF connector no problems, then u probably need to replace the auto toner sensor.
dear sir,
i have buy toshiba statellite pro in dubai 2008. but shope men not give me any other cd to driver and sfothwere. so pl sport me to this help.
If your Toshiba Camileo HD-DV camcorder is not focusing properly, there are a few potential causes and solutions to try:
Check that the lens is clean and free from any smudges or fingerprints. Even a small amount of dirt or debris on the lens can affect the focus. If the lens is dirty, try cleaning it with a lens cleaning solution and a microfiber cloth.
Make sure the lens is not blocked by any foreign objects, such as the hood of a camera bag or the edge of a cap.
Try adjusting the focus manually using the focus ring on the lens. If the focus ring is not responding or is difficult to turn, the lens may need to be serviced.
Make sure your camcorder firmware is up to date. Check Toshiba website to see if there is any update available and instructions on how to update.
Make sure the camera is not in macro mode. Some cameras have a separate macro mode that enables the camera to focus on objects that are very close. If you are not trying to take close-up shots, you may need to switch out of this mode.
Make sure the scene is well lit. Low light can make it more difficult for the camera to focus, try adding more light to the scene or use the manual focus.
If none of the above steps work, it is possible that the camera's autofocus system may be malfunctioning and will need to be repaired. It's best to contact Toshiba customer service or a local camera repair shop for a diagnosis and estimate for repair if the issue persists
Your camera requires four AA size batteries.There are several factors that contribute to battery life:
NiMH: This is the best solution for enjoyment and cost savings. NiMH batteries typically last longer per charge than the average alkaline batteries. NiMH batteries are rechargeable batteries, so they can be used several times and thereby reduce the expense of continually purchasing new batteries. NiMH batteries are typically sold with a power adapter for charging. The life of these batteries can often be determined by the mAh rating, the higher the mAh rating on the battery, the longer that they will last. NiMH batteries do not have the memory effect associated with NiCd batteries, which means that these batteries can be recharged at any time and at your convenience (you do not have to wait for the batteries to completely drain between charges).
Lithium: Energizer has introduced a new series of Lithium batteries that provide optimum performance and long life for disposable AA size batteries. Laboratory studies shows that Lithium batteries last more than three times as long as standard Alkaline batteries. This means many more hours of fun and satisfaction with your digital camera. These lithium batteries are not rechargeable, they are long lasting.
Alkaline: Using the LCD display, downloading images, playback, zoom and flash all require some battery power to operate and may decrease the number of shots per set of batteries. Performance may also vary based on the Alkaline batteries selected. To significantly increase battery life, be sure to turn off the LCD when it is not in use. The LCD consumes the most amount of battery power. The benefit of being able to use alkaline batteries is that you can find then almost anywhere if needed.
Manganese: If you are using manganese batteries, the typical battery life will be about 2 - 5 shots. Then the camera will indicate that battery power is low and may shut-down. To avoid this experience, use either Alkaline or NiMH batteries.
Optimum Solution: Use a set of NiMH batteries for longer use and to reduce the expense of continually buying new batteries. It may also be a good idea to keep a spare set of NiMH batteries for other devices that require AA size batteries on a regular basis. Use AA Alkaline batteries when the NiMH batteries need to be recharged and you want to continue enjoying the use of your camera.
The error code F101 13 on a Toshiba e-Studio 4508A printer indicates that there is a problem with the fixing assembly. This can be caused by a number of issues, including a malfunctioning thermistor, a problem with the heating roller, or a problem with the temperature control system.
Here are some steps you can try to fix the error:
Check the thermistor: The thermistor is a temperature sensor that is located near the heating roller. Make sure that the thermistor is securely connected and not damaged.
Check the heating roller: The heating roller can become worn or damaged over time, which can cause the error. Inspect the roller for any visible damage and replace it if necessary.
Check the temperature control system: Make sure that the temperature control system is functioning properly and that the temperature is set correctly.
Restart the machine: Try turning the machine off and unplugging it for a few minutes before restarting it. Sometimes this can clear the error.
If the error persist after trying these steps, it's likely that there's a hardware issue in the fixing assembly that will need to be repaired by a service technician. They will be able to diagnose the specific issue and repair or replace the necessary parts.
It's best to refer to the service manual of the copier/printer or consult with an authorized technician before taking any steps. An unexpected move may cause further damage.
The remote control for your DVR has the capability to control 2
additional DVRs in addition to the one that you currently have. In
order for the remote control to work with your DVR, you will need to
make certain both of them are talking on the same frequency. If you
press the remote control and the front of your unit says DR2, that
means that you need to have your remote on DR2 as well so that it can
operate the DVR. To set your remote to DR2, you will need to make sure
the unit is off then you will need to press and hold down the SETUP
button and while you are holding this button down, press the number 2
button. Your remote is now set to DR2.
Hi,
please attempt to change the input from the Toshiba recording device directly. You might switch between modes on the Toshiba by pressing 1 of the hdd, vcr or dvd buttons. If this doesn't work, you can power cycle the device and then attempt to changed the mode from the Toshiba directly again. Otherwise, you might need to eject any disc that's currently in the device before attempting to change modes again.
Thank you.
The idle tire for your VCR is either dirty or has worn out and has stopped the tape reel from being able to move and turn and also the rubber parts need to be replaced or cleaned as ell.
