Vision Fitness Recent Questions, Troubleshooting Help & Support

Question edited for clarity and toss in some CAPS. It is sold as an entry level fitness bike, but try the troubleshooting or contact them direct.

Troubleshooting ' Vision Fitness - United States

Vision Fitness https://www.visionfitness.com > eng > support > troubl... Make sure the treadmill switch is turned on. Solution: Check the power cable for crimping. Unplug the treadmill from the wall outlet, then wait 60 seconds to ... ..

I have this same issue, have you found a solution?

Question moved from Motorcycles to the correct category. Page 15 of the Service Manual refers

Vision Fitness E1500 Frame 9, R1500 Frame 9 Service Manual ...

https://manualzz.com > Vision Fitness > E1500 Frame 9 Vision Fitness E1500 Frame 9, R1500 Frame 9 Service Manual ' Manualzz ... FRAME_9) 14 4.8 EP240-2KM-F(X20 FRAME_9) CHAPTER 5 ERROR CODE 5.1 E1: No connect ... ..

question edited for clarity 'make model (what is is)'. Question moved form Cars and Trucks category to the right one! Service Manual Page 19 and troubleshooting guide https://www.google.com/search?q=vision+s7100hrt+reistance+not+working ..

Your diagnosis is good. The wheel should be more centred. You are not alone. Contact the maker, the details are in the link. https://www.google.com/search?q=vision+fitness+u40+grinding+noise ..

it is no PC,post to fitness machines.the makers OEM does not sell schematics but may sell service manuals ask them first.post here not PChttps://www.fixya.com/troubleshoot/browse/fitnessplease

https://content.johnsonfit.com/inc/uploaded_media/5909b6a4720ac96262abbd62767ed35d/troubleshooting_guide/87fc08ffe3e0caa8a9d3a1b15d59e71d.pdf

Try to check the carbon brush of the motor. If it's OK then the motor control board would be faculty If you wish to get some more details about treadmill repair then check the following link http://electro-medical.blogspot.com/

https://www.youtube.com/watch?v=Ww6Ns4GwhYw https://www.youtube.com/watch?v=l6VauCpABhQ

Dear Sir:Please see the diagram attached from REED switch, adjust, clean, and tight the connector wires very well.2) change the batteries by new ones, use the best.clean the contact batteries.3) tight the ribbon cable from keypad .+ tight the connector from display board vs lower board.4) after you fix it RUN THE sofware calibration for diagnose, troubleshooting, See my personal tips for helpsincerely. God bless you

If you wish to get some details; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

If you wish to get some details; check the site linked here. Pull up older posts treadmill . Surf the site with patience. http://electro-medical.blogspot.com/

1)probably a faulty speed sensor 2) the speed sensor is not plugged in properly.3) possibly a faulty motor test for 115 vca without load 4) control board or lower board for measure 115 vca and +5vca 5) Run the calibration sofware for easy diagnotic see the diagram attached.6) Test the transformer for primARY VOLtage and secondary voltage. see the TIP. The error codes will differ between makes and models but could be e1.http://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnesshttp://www.fixya.com/support/r10786838-test_procedure_dc_motorSincerely. Happy New Year . G-d bless youernesto cuadramanagua,nicaragua c.a.

If you wish to get some details; check the site linked here. Pull up older posts treadmill . http://electro-medical.blogspot.com/ Surf the site with patience.

First thing to do with these folding vision fitness treadmills is REPLACE THE MAINS SUPPLY CABLE They were supplied with very poor quality cable that cause issues like juddering stopping and speed fluctuations.

My guess is the drive belt has come off. Open the plastics up slightly and look in with a torch.