Whirlpool Washing Machines - Page 3 - Popular Questions, Answers, Tips & Manuals

Question edited for clarity Whirlpool error F18 Error code F18 indicates there's too much foam in the drum. Thankfully, this problem is easy to solve. Unload the drum and run a wash cycle without soap. This removes excess foam. Jan 30, 2023

The most common errors of Whirlpool washing machines

coolblue.nl https://www.coolblue.nl > advice > help-most-common-e...

Quite simply you locate the leak and replace the hoses, gaskets or the part that is leaking. A trick is to slip some paper under it and pull it out after a few minutes to see the area of the leak. Then you can pull the machine out and tip it back against the wall to check the location.

Did you try a power reset? Remove the mains plug overnight. It will reset the electronic mainboard. Normally, they spin or they don't. https://www.google.com/search?q=Whirlpool+wfw75hefw+not+spinning+on+program ..

They are all shown here

washing-machine-cycle-time-chart.pdf - Whirlpool

Whirlpool https://www.whirlpool.com > en-us > blog-posts PDF *Cycle times represent Whirlpool products and may vary by model. How much time do you have while your clothes are washing? Check our chart for an estimate. 1 page ..

Question moved from Cars and Trucks. All questions need full 'make model (what it is)'. That will put you into the right category. I moved you to Whirlpool. The Door lock has failed. https://www.google.com/search?q=Washer+F22+Error ..

If you're finding grease under the washplate of your Whirlpool top load washer, it's likely that the transmission is leaking. The transmission is responsible for turning the drum during the wash cycle, and if it is leaking, it can cause grease to build up under the washplate. Here are a few steps you can take:

1. Check the transmission oil level: The first step is to check the oil level in the transmission. If the oil level is low, it could indicate a leak.
2. Check for leaks: Look for any visible leaks coming from the transmission. If there are leaks, it's best to take it to a qualified repair technician.
3. Clean the washplate and drum: Clean the washplate and drum with warm soapy water and a soft cloth. Be sure to remove any debris or buildup that may have accumulated.
4. Check the transmission oil seal: the oil seal may be the cause of the leak, if it's damaged or worn out, it will need to be replaced by a professional technician.

It's important to keep in mind that the transmission is a complex component, and if you're not comfortable working with it, it's best to consult a professional technician for further diagnosis and repair. It's also important to note that some of these steps require a certain level of mechanical knowledge and experience. If you're not comfortable with checking these items, it's best to consult a professional repair technician if i was able to help my cashapp $ralphpapi thank you have a blessing day

It sounds like the Start/Run Capacitor has failed on the motor control board. The motor buzzes when they fail. The capacitor gives the motor a jolt of power to get it turning.

To replace the spring on your Whirlpool washer SM8525492-B, you may need to remove the upper control panel. Here are some steps you can follow to do this:
1. Unplug the washer from the electrical outlet to ensure your safety.
2. Remove the end caps on each side of the control panel. These end caps are located at the top of the washer and can be removed by pulling them off.
3. Once the end caps are removed, use a screwdriver to remove the screws that hold the control panel in place. There should be two screws, one on each side of the control panel.
4. Once the screws are removed, slide the control panel forward to release it from the clips that hold it in place.
5. Tilt the control panel back and rest it against the wall. Be careful not to damage any of the wires or connections that are attached to the control panel.
6. You should now have access to the springs on the washer. Replace the spring as necessary, and then reattach the control panel by reversing the steps above.

If you are still having trouble removing the control panel, it may be helpful to consult the washer's manual or contact a professional for assistance.

The washing machine is not balanced. This might be caused by the washing machine being very packed too tightly or the clothing is not distributed. Or an uneven load.

The error code "F" followed by a number and a dot on a Whirlpool Cabrio washing machine indicates a fault has been detected in the machine's control board. Without the specific number that follows the "F," it is difficult to determine the exact issue. You can try unplugging the machine for a few minutes and then plugging it back in to see if the error code clears. If the code persists, you may need to consult the user manual or contact Whirlpool customer service for further assistance.

We had this happen to our Kenmore washer. Your solution might be the same as ours. The reason that the agitation cycle won't start is that the safety switch that senses door closure is out of adjustment or broken. They're hard to get at on our Kenmore, so I just took a short length of fish tank plastic air supply hose and slid it over the probe on the door that pushes the switch open. The added length (try half an inch), was enough to push the safety switch and start the agitation cycle. It's not elegant, but has been a permanent solution for us!

If you need a control knob assembly for your Whirlpool LSQ9564MQ0 washing machine, there are several options you can explore:

1. Contact Whirlpool Customer Service: You can reach out to Whirlpool customer service to see if they have the part available for purchase. You can call them at 1-800-253-1301 or visit their website to chat with a representative.
2. Check Online Retailers: There are several online retailers that specialize in appliance parts, such as PartSelect, RepairClinic, and AppliancePartsPros. You can search for the control knob assembly for your specific model and order it online.
3. Check Local Appliance Repair Shops: You can also check with local appliance repair shops in your area to see if they have the part or can order it for you.

When replacing the control knob assembly, be sure to follow the manufacturer's instructions and turn off power to the appliance before beginning any repairs.

ck here...... https://www.appliancepartspros.com/repair-help/whirlpool-washer-lxr6232eq0-repair/lxr6232eq0-will-not-stop-filling-with-water.html

You can check to see if there is a quick fix by doing the following:

• Verify the power source: Check to see if the dryer is plugged in and if the circuit breaker hasn't tripped. Reset the circuit breaker to see if the dryer comes on if it has been tripped.
• Examine the doorknob: The dryer might not start if the door switch is broken. Open and close the dryer door to check that the door switch is functioning properly. The door switch may need to be replaced if the dryer starts when the door is closed.
• Examine the thermal fuse: If the dryer gets too hot, the thermal fuse, a safety feature, can stop the machine from working. The thermal fuse will need to be replaced if it blows.
• Examine the control panel: The control board may be defective and need to be replaced if none of the aforementioned steps resolve the issue.

Here you go LSQ9549L

Question edited for clarity. Question moved from Computers to Whirlpool Washing Machine. Question translated to English, we only speak English on this North American website! This error code will be displayed if the machine is trying to fill with water but the flow meter doesn't sense any flow for 30 seconds. In this case, check the water supply to be sure you have good pressure for both hot and cold water. Then, consider replacing the flow meter.

Whirlpool F/H - FH No Water Entering Machine or Pressure ...

The drive belt cold be faulty and will need to be replaced.