Bernard D'Souza posted an answer for this The Office Equipment & Supplies:
"Ricoh fusing errors are a problem, as sometimes to reset the error you may require a FUSE..."
Bernard D'Souza posted an answer for this Kyocera Office Equipment & Supplies:
"Check development unit. Broken gear or drive or motor."
Bernard D'Souza posted an answer for this Kyocera Office Equipment & Supplies:
"Check dev unit cable. And confirm that all doors are closed properly."
Bernard D'Souza posted an answer for this Kyocera Office Equipment & Supplies:
"Scanner lock enabled(Transportation lock) or dirty home position sensor."
Bernard D'Souza posted an answer for this Ricoh Office Equipment & Supplies:
"Bad Magenta Development unit"
Bernard D'Souza posted an answer for this Kyocera Copystar CS-2560 Black and White Copier:
"Check the development unit and the connector"
Bernard D'Souza posted an answer for this Kyocera Mita KM-2550 All-In-One Laser Printer:
"Related to the power supply or power supply pcb"
Bernard D'Souza posted an answer for this Kyocera Office Equipment & Supplies:
"try upgrading the firmware"
Bernard D'Souza posted an answer for this Kyocera FS1320D Laser Printer:
"need to pump toner inside the dev unit =open and close main door 10 to 15 times slowly."
Bernard D'Souza posted an answer for this Kyocera KM-1505 Copier:
"fuser error"
Bernard D'Souza posted an answer for this Kyocera TASKalfa 180 Copier:
"select continuous scan"
Bernard D'Souza posted an answer for this Kyocera Copystar Printing Systems - 1503LG0KL0 All-In-One Laser Printer:
"paper size problem"
Bernard D'Souza posted an answer for this Kyocera Office Equipment & Supplies:
"details please ? model 6400 == fuser error"
Bernard D'Souza posted an answer for this Kyocera TASKalfa 180 Copier:
"dirty optics(scanner unit) clean the mirrors and lamp in the scanner area"
Bernard D'Souza posted an answer for this Kyocera Office Equipment & Supplies:
"check if eco saving mode is enabled."
Bernard D'Souza posted an answer for this Kyocera FS-4000DN Laser Printer:
"press drum unit open left door and push drum inside."
Bernard D'Souza posted an answer for this Kyocera FS4020DN (A4) Workgroup Mono Laser (Duplex+Networked) 128MB 1200dpi 45ppm 600 Sheet Printer:
"check for jamed paper above the paper tray in the duplex unit. =remove tray =move green..."
Bernard D'Souza posted an answer for this Kyocera Fs-3920dn Laser Printer:
"Open left door(waste toner bottle) push drum unit inside."
Bernard D'Souza posted an answer for this Kyocera TASKalfa 180 Copier:
"details????"
Bernard D'Souza posted an answer for this Kyocera FS1128MFP AllInOne Laser Printer:
"waste toner full try emptying the waste toner from the drum unit if possible. replace drum..."
Bernard D'Souza posted an answer for this Kyocera TASKalfa 180 Copier:
"fuser related =clear jam if any. =reset error clear - 1-0-8-7-1-0-8-7 --..."
Bernard D'Souza posted an answer for this Kyocera Copystar CS-1820 Black and White Copier:
"Scanner related =Check if the scanner lock(transportation) is on(should be off). =Clean..."
Bernard D'Souza posted an answer for this Kyocera 14537 Km 3050 4050 5050 Toner 34000 Yield:
"Select continuous scan and also multi-page tiff or pdf file format"
Bernard D'Souza posted an answer for this Kyocera Mita Utax Cd-1316 Compatible Copier Toner 6000Pgs Black Replaces Tk112 Kyocera:
"Error 6000 is fuser related. Broken fuser lamp error =bad thermistor =broken thermal..."
Bernard D'Souza posted an answer for this Office Equipment & Supplies:
"drum related error"
Bernard D'Souza posted an answer for this Office Equipment & Supplies:
"0180 == Machine number mismatch Machine number of main and engine does not match. ==Data..."
Bernard D'Souza posted an answer for this Kyocera Mita KM-1650 All-In-One Printer:
"install scan file utility on the new pc and then configure it. then add that pc to the..."
Bernard D'Souza posted an answer for this Office Equipment & Supplies:
"sc 360 = black toner sensor error(in the development unit)"
Bernard D'Souza posted an answer for this Office Equipment & Supplies:
"is the image shifting ? may be registration clutch or sensor"
Bernard D'Souza posted an answer for this Office Equipment & Supplies:
"brand? model?"
Bernard D'Souza posted an answer for this Office Equipment & Supplies:
"possible toner drive belt(very difficult to replace)"